Advertisement
Quick Links
Pack 03
B U I L D
I N S T R U C T I O N S
STAGE 16: ASSEMBLING THE LEFT AIR FILTER
STAGE 20: ATTACHING THE ALTERNATOR
BOX AND FIT TING PETROL PIPES
STAGE 21: INSTALLING THE CLUTCH
STAGE 17: CONSTRUCTING THE ENGINE
STAGE 22: FITTING ESSENTIAL ENGINE PARTS
STAGE 18: ATTACHING THE TRANSMISSION
STAGE 23: OIL PUMP AND BREATHER SYSTEM
STAGE 19: FIXING THE CRANKCASE COVER
AND OIL SUMP
STAGE 24: THE REAR FRAME
The "Automobili Lamborghini" and "Automobili Lamborghini Bull and Shield" trademarks, copyrights,
designs and models are used under license from Automobile Lamborghini S.p.A, Italy.
Advertisement
Related Manuals for Agora LAMBORGHINI MIURA Pack 03
Summary of Contents for Agora LAMBORGHINI MIURA Pack 03
- Page 1 Pack 03 B U I L D I N S T R U C T I O N S STAGE 16: ASSEMBLING THE LEFT AIR FILTER STAGE 20: ATTACHING THE ALTERNATOR BOX AND FIT TING PETROL PIPES STAGE 21: INSTALLING THE CLUTCH STAGE 17: CONSTRUCTING THE ENGINE STAGE 22: FITTING ESSENTIAL ENGINE PARTS STAGE 18: ATTACHING THE TRANSMISSION...
- Page 2 Advice from the experts Spare screws are included with each part. Occasionally, you may be instructed to keep spare or unused screws for a later stage. Keep these spares in a safe place and label them correctly. Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary slightly.
- Page 3 Stage 16: Assembling the Left Air Filter Box and Fitting Petrol Pipes In this stage you’ll assemble the left air filter box, then it’s time to fit the carburettors from the last pack with petrol pipes. S T A G E 1 6 P A R T S L I S T Name Air filter box Air filter box cover...
- Page 4 Stage 16: Assembling the Left Air Filter Box and Fitting Petrol Pipes First take the air filter box cover and the three air filter box screws. Turn the box cover over, then align the air filter box with it as shown. Carefully push the screws into the holes in the cover (arrows).
- Page 5 Stage 16: Assembling the Left Air Filter Box and Fitting Petrol Pipes Cut the petrol pipe fittings from their sprue using sprue cutters by Fit the petrol pipes onto the ends of the fittings as shown. We snipping at the points indicated by red arrows. recommend using a pair of tweezers to grip and twist the petrol pipe as you push it on.
- Page 6 Stage 16: Assembling the Left Air Filter Box and Fitting Petrol Pipes Now take the two carburettors assembled in stages 11 and 12 along The carburettors should look like this once in place. with the left cylinder head from stage 13. Press the pins on the carburettors into the holes between the spark plugs simultaneously, as you did in stage 15 (arrows).
- Page 7 Stage 16: Assembling the Left Air Filter Box and Fitting Petrol Pipes S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 8 Stage 17: Constructing the Engine Now the engine starts to take shape! After attaching the cylinder heads to the base, you’ll begin to add detail to the engine, starting with fitting the two air filter boxes over the velocity stacks. S T A G E 1 7 P A R T S L I S T Name Engine base...
- Page 9 Stage 17: Constructing the Engine TYPE A First place the engine base on your work surface, then fit the left While holding everything in place, turn the assembly over and secure cylinder head onto the engine base as shown. the cylinder head to the engine base using 2x Type A screws. We recommend removing the carburettors from the cylinder head before driving the screws in to avoid damaging the velocity stacks.
- Page 10 Stage 17: Constructing the Engine LEFT RIGHT Now take the two air filter boxes, one from the previous stage and the other from stage 10. Note the difference between the air filter boxes on the left and right air filters (arrows), as well as the ‘L’ and ‘R’ printed on the underside of them to help differentiate the two. Once you’ve identified the air filter boxes, align them with the engine Fit the left air filter box onto the left cylinder head using the support block as shown.
- Page 11 Stage 17: Constructing the Engine Push the right air filter box onto the other side. The air filter boxes should look like this when in place. S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 12 Stage 18: Attaching the Gearbox Next you’ll build the gearbox and install it on your engine, then cover the lower engine up by adding the crankcase closure. S T A G E 1 8 P A R T S L I S T Name Transmission/differential housing Lower engine crankcase closure...
- Page 13 Stage 18: Attaching the Gearbox Take the housing cap and the left differential cover. Note the pins on Fit the cap into the cover so that the D-shaped holes in both parts the cap (circled) and the corresponding holes on the cover (arrows). align as shown.
- Page 14 Stage 18: Attaching the Gearbox Now align the right differential cover with the assembly. Press the pins The differential assembly should now look like this. on the back of the right cover into the holes of the left cover (arrows). Take the transmission/differential housing and 2x Type B screws.
- Page 15 Stage 18: Attaching the Gearbox TYPE B Secure in place using 2x Type B screws. Align the assembly with the engine block as shown. The two columns fit under the protruding tabs from the engine block (arrows). TYPE B TYPE B Push the assembly into place, then secure with 2x Type B screws.
- Page 16 Stage 18: Attaching the Gearbox TYPE A Fit the cover onto the engine base, then drive 2x Type A screws through the holes to secure everything together. S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 17 Stage 19: Fixing the Crankcase Cover and Oil Sump The impressive engine continues to take shape as you add the crankcase cover to the side and oil sump cover underneath. S T A G E 1 9 P A R T S L I S T Name Crankcase cover Oil sump...
- Page 18 Stage 19: Fixing the Crankcase Cover and Oil Sump TYPE B Take the crankcase cover and two Type B screws. The cover fits over Press the cover onto the engine block as shown, then secure with the protruding screw holes on the engine block (arrows). 2x Type B screws.
- Page 19 Stage 19: Fixing the Crankcase Cover and Oil Sump TYPE A Secure the oil sump using 2x Type A screws. Finally take the oil sump cover. Note the four pins on the cover and the corresponding holes (circled). Press the cover firmly onto the oil sump as shown, until the fit is flush all the way round the edges. AGORAMODELS LAMBORGHINI MIURA...
- Page 20 Stage 19: Fixing the Crankcase Cover and Oil Sump S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 21 Stage 20: Attaching the Alternator This stage is all about the alternator, which converts mechanical energy into electrical energy to charge the car’s battery. Take care when assembling it as some of the parts can be fragile! S T A G E 2 0 P A R T S L I S T Name Alternator cover Alternator bracket...
- Page 22 Stage 20: Attaching the Alternator TYPE A First take the alternator bracket and locate its mounting on the corner Fit the bracket in place and secure with 1x Type A screw. The inset of the engine block (arrow). shows the correct orientation for the bracket. Next fit the alternator cover and base together by pressing the pin into Align the alternator with the bracket on the engine block as shown.
- Page 23 Stage 20: Attaching the Alternator Push the large pin in place (circled), then lower the alternator into Take the fan and drive belt. Fit the pin on the drive belt through the the bracket you fitted earlier. Gently spread the bracket’s arms apart fan, then press into place on the alternator (arrows).
- Page 24 Stage 20: Attaching the Alternator S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 25 Stage 21: Installing the Clutch Next you’ll add the clutch onto your engine. The control spring in this stage can be difficult to attach, take your time to connect it! S T A G E 2 1 P A R T S L I S T Name Clutch bell Clutch bell cover...
- Page 26 Stage 21: Installing the Clutch Align the holes on the clutch bell cover with the pins on the clutch bell Push the cover onto the clutch bell until the fit is flush. as shown (arrows). Place the engine assembly onto your work surface as shown, and Gently press the clutch bell onto the engine so that the cover is locate the pin for attaching the clutch bell (circled).
- Page 27 Stage 21: Installing the Clutch Next take the clutch master cylinder. The two pins on the cylinder Press the cylinder into the holes, orienting it as shown. (inset, arrows) will be inserted into the holes in the engine, next to the clutch bell (circled).
- Page 28 Stage 21: Installing the Clutch The clutch spring has two hooks at each end, one faces up and the The clutch release mechanism cover has two protruding tabs (circled) other down. Using tweezers, first connect the end facing downwards which will be inserted into the rectangular holes on the clutch bell to the cylinder (red arrow).
- Page 29 Stage 21: Installing the Clutch S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 30 Stage 22: Fitting Essential Engine Parts You’ll install various parts that feed the oil and petrol needed by the engine to operate, as well as the water pump which keeps it from overheating and the starter motor that ignites it. S T A G E 2 2 P A R T S L I S T Name Engine support...
- Page 31 Stage 22: Fitting Essential Engine Parts First take the water pump which fits onto the side of the engine where Press the water pump into the engine block as shown. the alternator is located. Note the two holes for mounting the water pump (arrows).
- Page 32 Stage 22: Fitting Essential Engine Parts Now turn the engine assembly around as shown. Take the engine oil Push the parts into place (circled). Note the orientation of the engine connector pipe, the engine support and the starter motor. Locate the support in the photo, with its cylinder close to the starter motor (inset).
- Page 33 Stage 22: Fitting Essential Engine Parts Take the carburettor petrol pipe and the T-shaped connector. Fit the Then fit the connector onto the end of the longer petrol pipe fitted in pin of the connector into one end of the pipe as shown (arrow). stage 16 (circled).
- Page 34 Stage 22: Fitting Essential Engine Parts S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 35 Stage 23: Oil Pump and Breather System Next you’ll install the oil pump and breather, along with the filler cap. The pump feeds fuel from the sump to the engine, while the oil breather system catches oil suspended in the gases and stops pressure building up.
- Page 36 Stage 23: Oil Pump and Breather System Take the oil breather separator box along with the engine assembly. The oil breather separator box has a shaped pin that corresponds to Locate the shaped hole on the right cylinder head (circled). the hole on the cylinder head (inset).
- Page 37 Stage 23: Oil Pump and Breather System Now take the oil filler cap, noting the shaped pin (inset). This fits Finally, take the oil breather pipe. Note that one end has a flange into the corresponding hole on the left cylinder head, next to the oil (circled), while the other has only a pin (arrow).
- Page 38 Stage 23: Oil Pump and Breather System S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
- Page 39 Stage 24: The Rear Frame In the final stage for this pack, you’ll begin to prepare the rear frame which will be used for mounting the engine and the rear suspension. S T A G E 2 4 P A R T S L I S T Name Rear frame Front support for lower suspension...
- Page 40 Stage 24: The Rear Frame The frame will support the engine, with the widest part facing towards Before attaching the supports to the frame, we recommend the front of the car and the narrowest part towards the rear. Note the driving the spare screw into the two holes indicated in the previous two screw holes indicated by arrows.
- Page 41 Stage 24: The Rear Frame TYPE A Fix the supports in place using 2x Type A screws. Check that both supports are firmly affixed to the frame. If there is any wobble, take the screw out and apply oil to help drive the screw in securely. AGORAMODELS LAMBORGHINI MIURA...
- Page 42 Stage 24: The Rear Frame S T A G E C O M P L E T E AGORAMODELS LAMBORGHINI MIURA...
Need help?
Do you have a question about the LAMBORGHINI MIURA Pack 03 and is the answer not in the manual?
Questions and answers