Battery Jump-Starting Safety - Peak PKC0J1200 Owner's Manual And Warranty Information

Battery Jump-Starting Safety

EXPLOSIVE GASES — Do not use this product in the presence of flammable fumes
or gases. Working in the vicinity of a lead-acid battery can cause an explosion of the
battery being charged. When lead-acid batteries are charging, they vent explosive
hydrogen gas, which can be ignited by sparks from electrical connections. It is
important to read this manual before charging and follow the jump-start instructions
exactly (see page 7) each time you use this Jump-Starter.
• Do not smoke or use flammable items (matches, cigarette lighters, etc.) while working on a
vehicle's battery system.
• Never jump-start a frozen battery, as it could explode.
• Perform all jump-starting procedures in a safe, dry, well-ventilated area.
• Do not expose battery to fire or intense heat since it can explode.
• Before recycling or disposing of a battery, protect exposed terminals with heavy-duty electrical tape
to prevent shorting (shorting can result in personal injury or fire).
• Always wear protective eyewear when using this product. Contact with battery acid can cause
blindness and/or severe chemical burns.
• Follow these first aid procedures in case of accidental contact with battery acid.
FIRST AID
SKIN: Wash skin thoroughly if battery acid comes in contact with skin. Seek medical attention
immediately.
EYES: Flush eyes with cool water for at least ten minutes. Seek medical attention IMMEDIATELY.
IF INGESTED, CONTACT POISON CONTROL CENTER IMMEDIATELY.
Never touch battery clamps together or to a common piece of metal. Sparking, explosion, or damage
to the unit can result. Always store the clamps in the appropriate holders on the back of the unit after
use.
• Place this unit as far away from the battery being jumped as the jumper cables will permit.
• When using the Jump-Starter close to the vehicle's battery and engine, place the unit on a flat,
stable surface, and keep all clamps, cords, clothing and body parts away from moving parts of the
vehicle.
• Follow these instructions and those published by the battery manufacturer and manufacturer of
any equipment you intend to use near the battery. Pay attention to all hazard precautions on these
products and on the engine before charging.
• This system is designed to be used only on vehicles with a 12-volt DC battery system. Do not
connect to a 6-volt or 24-volt battery system.
• Remove all jewelry or metal objects that could cause short circuits or react with battery acid. A
lead-acid battery produces a short circuit current high enough to weld a ring or other similar objects
to metal, causing a severe burn.
• When working on electrical equipment, always ensure someone is nearby to help you in an
emergency.
• Keep a supply of baking soda on hand when working on batteries. Baking soda neutralizes lead-
acid battery electrolyte.
All messages that follow have NOTICE level hazards. Failure to comply could
result in property damage.
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-
started. Before jump-starting, read the vehicle's owner's manual to confirm that external-starting
assistance is suitable.
• Excessive engine cranking can damage a vehicle's starter motor. If the engine fails to start after
the recommended number of attempts, discontinue these jump-start procedures and look for other
problems that may need to be corrected.
• This Jump-Starter is not designed to be used as a replacement for a vehicle's battery. Do not
attempt to operate a vehicle that does not have a battery installed.
• After connecting the battery charging clamps to the discharged battery and before turning on the
Jump-Starter OFF/Jump Switch, check the jump-starter ON indicator on the front of the unit. If the
reverse clamps light turns RED and an alarm sounds, the clamp connections are incorrect and
need to be reversed.
• This Jump-Starter is delivered in a partially charged state. Fully charge unit with the supplied
110/120-volt AC charger to the initial charge time of 40 hours. Thereafter, an AC typical charge
time is 22 to 26 hours when using the 110/120-volt AC charger.
• Although this unit contains a sealed battery, it is recommended that the unit be kept upright during
storage, use and recharging. To avoid possible damage that may shorten the unit's working life,
protect it from direct sunlight, direct heat and/or moisture.
3