Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crystal Vision Indigo ADP 310
Summary of Contents for Crystal Vision Indigo ADP 310
- Page 1 ADP 310 Audio delay and processor for discrete AES or analogue audio Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England. Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059 sales@crystalvision.tv www.crystalvision.tv...
-
Page 2: Table Of Contents
Crystal Vision ADP 310 User Manual Contents Introduction Hardware installation 2.1 Board configuration Link Configuration 2.2 Input and output piggyback boards 3G-AIP2 Analogue Input 3G-AOP2 Analogue Output DIOP4 AES I/O Fitting the I/O piggybacks onto the main board Rear modules and signal I/O... - Page 3 Crystal Vision ADP 310 User Manual Controlling cards via VisionWeb Control Descriptions Status Menu Status Audio Settings Menu Delay, Invert & Mono Audio Gain AES Output Router AOP Output Router Presets, Reset & GPI/Os Menu Presets Resets GPO5 / GPO6 Alarms...
- Page 4 Crystal Vision ADP 310 User Manual AOP Router Audio OP Chs Embed Mute AES Output Router Audio Op Channels Diop Mutes GPI outputs AES I/O GPO5 / GPO6 GPI outputs Analogue I/O GPO5 / GPO6 Presets and Reset Preset Board Reset Revision 1 Moved Statesman info to Appendix.
-
Page 5: Introduction
GPI control of configuration set-ups and status alarms. • Supports the following rear module connectors: RM47, RM74. • Compatible with Crystal Vision standard frames available in 2U, 1U and desk top box. ADP 310 User Manual R1.2 19 June 2019... - Page 6 Crystal Vision Introduction ADP 310 Functional Block Diagram Block Diagram Description All analogue or digital audio is passed to audio processing blocks where gain and delay adjustments are made after resampling. Dolby E encoded signals automatically bypass the audio processing stage.
-
Page 7: Hardware Installation
Crystal Vision Hardware installation 2 Hardware installation 2.1 Board configuration ADP 310 board top-side Note : The potentiometers P1, P2, P3 and P4 have been factory set and should NOT be adjusted. Holes marked ‘B’ are for the fitting of the I/O piggybacks. -
Page 8: Input And Output Piggyback Boards
Crystal Vision Hardware installation 2.2 Input and output piggyback boards The ADP 310 board has two positions where one of three types of I/O module can be plugged in to enable analogue or digital input and output. The front position is for audio inputs and the rear for outputs. -
Page 9: Aop2 Analogue Output
Crystal Vision Hardware installation 3G-AOP2 Analogue Output This analogue piggyback has four balanced audio outputs. The links PL1-4 set 0dBFS to +18dBu (to the right, towards SK2/3) or +24dBu (to the left, towards SK1). The four potentiometers P1-P4 are factory set and should NOT be adjusted. -
Page 10: Fitting The I/O Piggybacks Onto The Main Board
Crystal Vision Hardware installation Fitting the I/O piggybacks onto the main board Example showing 3G-AIP2 and 3G-AOP2 piggybacks fitted The I/O piggybacks plug onto the main board such that main board plugs J3, J4, J5 and J6, J7, J8 align with piggyback sockets SK2, SK3, SK1. With the component side of the module top-most, align the piggyback sockets carefully with the plugs and push firmly. -
Page 11: Rear Modules And Signal I/O
Crystal Vision Rear modules and signal I/O 3 Rear modules and signal I/O The 2U Indigo 2 frame will house up to 12 single height modules with a single or dual power supply. The 1U Indigo 1 frame will house six single height modules and a single or dual power supply. - Page 12 Crystal Vision Rear modules and signal I/O Module Pin-out position Analogue audio input C1 / AES1 Analogue audio input C2 / AES2 Front (Input) Analogue audio input C3 / AES3 Analogue audio input C4 / AES4 Analogue audio output C9 / AES5...
-
Page 13: Rear Module Connections With Rm74
Crystal Vision Rear modules and signal I/O Rear module connections with RM74 The RM74 is a dual height module presenting the eight unbalanced AES stereo pairs on 75 ohm BNC connectors. The DIOP4 I/O piggybacks must be used with this rear module as there is no provision for analogue audio I/O. -
Page 14: General Purpose Interface
Crystal Vision General Purpose Interface General Purpose Interface Introduction Each frame slot has up to six connections ‘a-f’ for GPI control and monitoring. These connections are available at the rear of the frame on the 26-way D-Type remote connectors. ADP 310 has four GPI inputs and two GPI outputs. -
Page 15: Alarms
Crystal Vision General Purpose Interface Alarms GPI Out 5 and 6 (e, f) can be configured to be asserted (logic ‘L’) for a selection of error conditions. There are, in total, a maximum of nine separate alarms for AES audio I/O and three for analogue audio I/O. -
Page 16: Frame Gpi Connections
Crystal Vision General Purpose Interface 1U frame GPI connections GPI lines ‘a’ to ‘f’ of each card connect to two rear remote connectors as follows: Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin 8 (1) -
Page 17: Control And Status Monitoring
Crystal Vision Control and Status monitoring 5 Control and Status monitoring ADP 310 controls and status can be accessed by either the card edge control, the rack front panel or by ‘VisionWeb’ remote control web browser software. ADP 310 is aware of what optional boards are fitted and adjusts the card edge/front panel menu tree accordingly to reflect the options available. -
Page 18: Reading Card Edge Leds
Crystal Vision Control and Status monitoring Reading card edge LEDs Card edge LEDs may be used in conjunction with status information from any connected remote status panel display or from VisionWeb if available. Refer also to the troubleshooting chapter for more help with solving problems and monitoring status information. -
Page 19: Using The Front Control Panel
Crystal Vision Control and Status monitoring 5.2 Using the front control panel At power up, the LEDs of all eight control panel keys will illuminate briefly. Once the panel has completed its power up and configuration sequence the panel will enter its status mode and display the current software version and frame IP address. -
Page 20: Control Panel Keys Overview
Crystal Vision Control and Status monitoring The ADP 310 home menu Rotate the shaft control to scroll through the menu structure and press ENTER to select the sub-menus. Press HOME at any time to return to the home menu. ADP 310 Reference Status sub-menu Press ENTER to select the Reference Status menu or SCROLL to display other sub- menus. -
Page 21: Menu Structure
Crystal Vision Control and Status monitoring Menu Structure The basic menu structure for card edge, front panel access and VisionWeb is identical and consists of the following groups and sub-groups. Note that some of these groups and sub-groups will change according to the piggyback boards fitted –... -
Page 22: Controlling Cards Via Visionweb
A more detailed description is in the section ‘Control Descriptions’. Controlling cards via VisionWeb Crystal Vision cards use an XML file to create a control database that is used by the card’s front-edge controller, the Indigo frame front panel controller and VisionWeb software. - Page 23 Crystal Vision Control and Status monitoring The example above shows an ADP 310 card fitted in slot one and the frame’s power supply and status monitor in slots 13 and 14. Clicking on the ADP 310 card will bring up the card’s home page: ADP 310 Status Page ADP 310 User Manual R1.2...
-
Page 24: Control Descriptions
The controls of ADP 310 are accessible from the front panel, the board edge or from Crystal Vision’s ‘VisionWeb’ software. The description of controls used in this manual is based on VisionWeb GUI screen grabs but the path to locate controls via the front panel or board edge follows the same logic. -
Page 25: Audio Settings Menu
Crystal Vision Control Descriptions Audio Settings Menu Delay, Invert & Mono Display status of incoming audio signals, invert and delay. Indicates when input channel is present (AES only). LED Present always on for analogue inputs. Indicates when input channel is silent. i.e. consistently below - Silent 63dBFS. -
Page 26: Audio Gain
Crystal Vision Control Descriptions Audio Gain Control the gain of the audio channels by ± 18dB relative to the input level up to the point where digital clipping will occur Select which audio group of four channels to apply gain to. Select AES C1-C4 or C5-C8 for... -
Page 27: Aes Output Router
Crystal Vision Control Descriptions AES Output Router Route AES audio inputs to AES audio outputs. Mute output channels. This menu is only available if DIOP4 piggybacks are fitted. Display current selections (green circles) and pre-select the cross point to be routed when the ‘Take’ button is pressed (red circles). -
Page 28: Aop Output Router
Crystal Vision Control Descriptions AOP Output Router Route analogue audio inputs to analogue audio outputs. Mute output channels. This menu is only available if the 3G-AIP2 and 3G-AOP2 piggybacks are fitted. Display current selections (green circles) and pre-select the cross point to be routed when the ‘Take’ button is pressed (red circles). -
Page 29: Presets, Reset & Gpi/Os Menu
Crystal Vision Control Descriptions Presets, Reset & GPI/Os Menu Presets Up to 16 user-defined configurations may be stored and recalled either from VisionWeb or through the use of external GPIs. Presets store the board setup data including operating mode card status. The presets are numbered 1-16. -
Page 30: Resets
Crystal Vision Control Descriptions Resets Reset the board to its default settings. Reset the board to default settings but leave preset memories unaffected. Fact. Res Exc Preset Reset the board to default settings and erase preset memories. Fact. Res Inc Preset... -
Page 31: Silence Alarm Delay
Crystal Vision Control Descriptions Assert if AES pair or analogue pair is silent (<-63dBFS) for the period set Silence by the Silence Alarm Delay control. Silence Alarm Delay Set the period that a signal must be silent before asserting an alarm. -
Page 32: Troubleshooting
Crystal Vision Troubleshooting 7 Troubleshooting Card edge monitoring The front edge of the card provides useful power rail monitoring and input status. ADP 310 front edge view See Card Edge Controls for explanation of card edge LEDs. The card edge LEDs and 10-digit display may be used in conjunction with status information from any connected remote status panel display or from VisionWeb or Statesman if available. -
Page 33: Specification
Crystal Vision Specification 8 Specification General Dimensions 100mm x 266mm module with DIN 41612 connector. Weight 200g. Power ADP 310 - 9 Watts. consumption Inputs Ref Video Black and Burst or tri-level sync 625/50, 525/60, 525/59.94. standards supported Return loss 50Mhz to 1.5GHz -15dB. - Page 34 Crystal Vision Specification GPI inputs Number and type: 4 x GPI inputs. Recall of presets. Active pull to ground, pulled up to +5V through 7 kohm. GPI outputs Number and type: 2 x GPI outputs, assignable to any of nine alarm condition such as loss of reference input, audio missing and audio channel silence (<-63dBFS).
-
Page 35: Appendix
Introduction The Crystal Vision Statesman PC control software is designed to control a range of Crystal Vision modules via Ethernet control from a PC. Statesman provides a user friendly means of configuring and operating Crystal Vision modules with the benefit of “see-at-a-glance”... -
Page 36: Control Descriptions
The controls of ADP 310 are accessible from the front panel, the board edge or from Crystal Vision’s Statesman software. The description of controls used in this manual is based on Statesman but the path to locate controls via the front panel or board edge follows the same logic. -
Page 37: Status
Crystal Vision Appendix 1 The board status is shown using a mixture of simulated LEDs and text information. As a general rule a green LED shows a good condition such as input present. A greyed Status LED will indicate an absence such as non-alarm or non-warning status. -
Page 38: Audio Input
Crystal Vision Appendix 1 Indicates the presence and silence of all audio inputs. Option to invert, convert channel pairs to mono and set a Audio Input global user delay. User delay selects the global 0 to 400ms delay for all channel pairs selected. -
Page 39: Aip/Aes Audio Ip
Crystal Vision Appendix 1 Aip/AES Audio Ip Present Indicates when input channel is present (AES only). LED always on for analogue inputs. Silent Indicates when input channel is silent. i.e. consistently below -63dBFS. Invert Select to invert channel. Select to mono channel pair. N.B. Only the 1... -
Page 40: Audio Gain
Crystal Vision Appendix 1 Gain controls will give ± 18dB of gain relative to the input level up to Audio Gain the point where digital clipping will occur. Audio Gain tab with DIOP4 in front position. Audio Gain tab with 3G-AIP2 in front position. -
Page 41: Channel Gain
Crystal Vision Appendix 1 Channel Gain Select Channels Select the audio group of four to apply the gain controls to. Use these controls to set the audio gain by +/- 18dB individually for each of the four channels of the group. Select the group first and then adjust the gain. Gain... -
Page 42: Aop Router
Crystal Vision Appendix 1 The 4x4 analogue output router allows any of the four analogue inputs to be routed to any of the four analogue output channels. The entire router configuration can be preset and activated with a single ‘Take’. All channels can be individually muted. -
Page 43: Aes Output Router
Crystal Vision Appendix 1 This 8x8 router is for routing AES signals to the digital audio output module. Any of the eight AES Output Router audio inputs can be routed to eight audio outputs. This tab appears whenever a DIOP4 piggyback is fitted in the rear position. -
Page 44: Diop Mutes
Crystal Vision Appendix 1 Diop Mutes For DIOP4 output piggyback. Output channels Ch9-16 Select to Mute output channel. N.B. Matrix output channels C9-16 correspond to rear module stereo pairs AES 5-8. The GPO 5 and GPO 6 outputs are reserved for alarm indication and may each be assigned to any of the video and audio alarm conditions. -
Page 45: Gpo5 / Gpo6
Crystal Vision Appendix 1 GPO5 / GPO6 Set the various conditions that assert GPO 5 and GPO 6. On if GPO is asserted. N.B. Visual indication of GPO 5 and GPO 6 status is provided on the Status board edge. -
Page 46: Gpi Outputs Analogue I/O
Crystal Vision Appendix 1 The GPO 5 and GPO 6 outputs are reserved for alarm indication and may GPI outputs each be assigned to any of the video and audio alarm conditions. Analogue Reference video and audio missing will assert an alarm immediately whereas the silence alarms can be assigned a delay timer to delay the time after which an alarm is asserted. -
Page 47: Gpo5 / Gpo6
Crystal Vision Appendix 1 GPO5 / GPO6 Set the various conditions that assert GPO 5 and GPO 6. Status On if GPO is asserted. N.B. Visual indication of GPO 6 status is provided on the board edge. Video Select to assert the alarm if the video reference is missing. -
Page 48: Presets And Reset
Crystal Vision Appendix 1 Up to 16 user-defined configurations may be stored and Presets and recalled either from Statesman or through the use of external GPIs. Presets store the board setup data Reset including operating mode card status. The presets are numbered 1-16. -
Page 49: Board Reset
Crystal Vision Appendix 1 Board Reset Reset ADP 310 settings to default values. Fact Res Exc Presets Reset the board to default settings but leave preset memories unaffected. Fact Res Inc Presets Reset the board to default settings and erase preset memories.
Need help?
Do you have a question about the Indigo ADP 310 and is the answer not in the manual?
Questions and answers