Table of Contents
Advertisement
200 SERIES TWO-MAN AUGERS
FORM GOM08042004US, VERSION 1.1
ACCESSORIES
NOTE: All auger bits, bit extensions, teeth and bit screws are for use in general
purpose projects for a variety of soil conditions unless otherwise specified. All
auger bits and auger bit extension drive connections are shown below are 1-3/8
inch (35 mm) hexagon. Digging depth for all augers is 36 inches (914 mm).
Planting auger digging depth is 30 inches (762 mm) and auger bit extension is
15 inches (381 mm).
Part #
BR10586
BR10587
BR10588
BR10589
BR10590
BR10591
BR10592
BR10593
5500-
15XBR
BR10614
BR10615
BR10616
BR10617
BR10618
BR10619
BR10620
BR10621
BR10622
BR10623
BR10624
BR10625
BR10626
BR10628
8 MACHINE SET-UP
Open shipping carton immediately upon receipt. Remove Auger from carton.
Visually inspect contents of carton for freight damage and/or missing parts. If
shipping damage is evident, contact delivering carrier immediately to arrange
for an inspection of damage by their claims representative. DO NOT DESTROY
OR DISCARD SHIPPING CARTON UNTIL INSTRUCTED BY AUTHORIZED
REPRESENTATIVE OF CARRIER OR FACTORY. If missing parts are
detected, notify your dealer who will assist you in obtaining them.
Description
Cutting
Weight
Diameter
(in lbs)
4 inch (102
4.5 inch
19.0
mm) Auger OD
(114 mm)
6 inch (152
7.5 inch
24.0
mm) Auger OD
(191 mm)
8 inch
9.5 inch
30.0
(203mm)
(241 mm)
Auger OD
10 inch (254
11.6 inch
36.0
mm) Auger OD
(295 mm)
12 inch (305
13.6 inch
48.0
mm) Auger OD
(345 mm)
14 inch (356
15.6 inch
54.0
mm) Auger OD
(396 mm)
16 inch (406
17.2 inch
61.0
mm) Auger OD
(437 mm)
18 inch (457
19.7 inch
40.0
mm) Auger OD
(500 mm)
No Flighting
NA
7.1
Auger Bit
Extension
Standard Dirt
NA
3.0
Tooth
Hardfaced Dirt
NA
3.2
Tooth
Chisel Type
NA
1.2
Dirt Tooth
Tungsten
NA
1.3
Carbide Dirt
Tooth
Tungsten
NA
1.2
Carbide Tooth
Screw Bit
NA
2.6
Hardfaced
NA
1.0
Screw Bit
Bit Screw
NA
4.2
Hardfaced
NA
1.5
Screw Bit
Bit Screw
NA
1.6
Hardfaced
NA
1.9
Screw Bit
Bit Screw
NA
3.2
Hardfaced
NA
4.5
Screw Bit
Auger Pin
NA
0.4
English-EN
INSTALLING OPERATOR HANDLES
Tools Required:
2 each, 1/2 inch (13 mm) wrench
1 each, 5/16 inch (8 mm) wrench
1 each, torque wrench, 240 inch pounds (27 Nm) capacity with 1/2 inch
(13 mm) socket
1 each, small Phillips screwdriver
1 each, small vice grip pliers
1 each, cut off pliers
Assemble operator handles to transmission on level working platform of
appropriate size and height. As an alternative, transmission driveshaft can be
securely mounted in suitable bench vice.
1.
Open assorted hardware bag into suitable container to prevent
component loss.
2.
Facing spark plug end of engine, install two curved non-throttle control
operator handles into transmission case sockets, arc of curve pointing
upward. Use supplied nuts, lock washers and flat washers with threaded
end of bolts facing upwards. FINGER TIGHTEN ONLY. DO NOT FINAL
TORQUE FASTENERS AT THIS TIME. FIGURE 2
FIGURE 2
3.
Facing fuel tank end of engine, install remaining curved non-throttle
operator handle into transmission case socket located under engine
governor control on left side per Step 2.
DANGER
•
Improper assembly and operation of Magura® throttle
control will reduce controllability of Auger, resulting in
property damage and/or personal injury.
4.
Install throttle control handle with throttle control grip in remaining
transmission case socket. Auger is designed for throttle control grip to be
operated by the right hand. DO NOT deviate from assembly and
operation of throttle control outlined in this manual. Reduced control of
Auger will result.
5.
Using torque wrench, torque all handle screws evenly to 240 inch pounds
(27 Nm).
CAUTION
Properly attached operator handles provide proper structural
•
integrity.
•
Use of Hole Digger without operator handles properly
attached can result in handle failure and/or personal injury.
7
Advertisement
Table of Contents
