Table of Contents
Advertisement
These operations are accessible by remote control.
Some may also be accessible by the main unit's control
panel.
Initial setup
This section will guide you through the unit's Initial setting which
includes selecting a language for your on-screen menu and
Autoprogram, which automatically scans and memorizes viewable
channels.
Before you begin:
Make sure the unit is connected to an antenna or cable.
1
After making all the necessary connections, press B to turn on
the unit.
It may take a few moments to turn on the unit for the first time.
●
Initial setup menu appears automatically after the unit is
●
turned on.
2
Use H I to select the on-screen language from the choices
(English / Español / Français) on the right side of the TV screen,
then press OK.
3
Use H I to select Voice guide to Off or On on the right side of
the TV screen, then press OK.
4
Use H I to select antenna for program local over the air channels
or unencrypted cable channels, then press OK.
5
Use H I to select HDMI or RF on the right side of the screen,
then press OK.
6
Use H I to select Antenna for TV channels or Cable for CATV
channels, then press OK.
Initial setup
Make sure the antenna is connected to "ANTENNA IN"
jack.
Select your signal source.
Antenna
Cable
Or
Select
OK
When Antenna is selected, the TV detects antenna signals.
–
It searches for DTV and analog TV channels available in your
area.
When Cable is selected, the TV detects signals supplied by
–
cable. It searches for DTV, analog TV and cable channels
available in your area.
Autoprogram will begin.
●
Initial setup
Please wait while the system is scanning for channels.
Auto programming may take more than 20 minutes to
complete.
0%
Digital channels
Analog channels
Antenna
Cable
Skip
ANTENNA IN
Back
Skip
0 ch
0 ch
Skip
7
Use H I to select the desired location setting, then press OK.
Initial setup
Location:
"Home" mode is optimized for efficient
energy usage for home use.
"Retail" mode is optimized for Store Demo
with fixed settings.
Select
Select Home, the unit is set to maximize the energy efficiency
●
for home setting and it can be adjusted through a choice of
picture and sound quality according to your preference. Use
this setting to remove the E-sticker, if visible on the display. L
p. 30
You must set Home in step 5. Otherwise, Picture and Sound
●
settings you adjusted will not be memorized after the unit goes
into standby mode.
When the Initial setup is completed, the lowest memorized
●
channel with the confirmation message of the location setting
will be displayed on the TV screen.
Select Retail, the unit will be set up with predefined settings
●
for retail displays.
Note(s)
If you are not receiving a signal from your cable service, contact the cable
●
provider.
If you press B or MENU during Autoprogram, this setup of TV channels will be
●
cancelled.
The initial Autoprogram function can be executed for either Antenna or Cable
●
only once. When you change the connection (Antenna / Cable), select
Autoprogram again. L p. 23
If there is no signal input from the antenna terminal and no operation for several
●
seconds after you turn on the unit, helpful hints appears. Follow the instructions
listed on the TV screen.
Initial setup
No channel is registered.
Try Autoprogram again?
Verify that you have a cable connected to the
ANTENNA IN jack on the back of the TV, the channel
installation process searches this connection.
If you are using a cable or satellite box, please confirm
the input which you have connected to the box and
press "SOURCE" key on the remote control to select
the appropriate source input.
####
####
Select
OK
After an initial setup is completed...
If you want to scan the channels automatically again.
●
Autoprogram L p. 23
You can add the desired cable and analog channels not memorized
●
by Autoprogram.
Add channels L p. 24
If you want to change to another language.
●
Language L p. 30
If you want to change the location setting.
●
Location L p. 30
15
.
English
Retail
Home
OK
Retry
Later
Skip
Advertisement
Table of Contents
