Makita DBM230 Original Instructions Manual
Diamond core drill
Hide thumbs
Also See for DBM230:
- Operating instructions manual (82 pages) ,
- Original instructions manual (112 pages)
Advertisement
Quick Links
D
Diamant-Kernbohrmaschine
Diamond Core Drill
GB
F
Carotteuse diamant à eau
I
Carotatrice ad umido
Taladro Para Broca de Diamante
E
corte húmedo
PT
Berbequim com broca de diamante
húmida
Diamantkernboor, nat gebruik
NL
DK
Våddiamantkerneboremaskine
Originalbetriebsanleitung
Original Instructions
Notice originale
Istruzioni originali
Instrucciones de servicio originales
Manual original
Oorspronkelijke gebruiksaanwijzing
Original brugsanvisning
Advertisement
Related Manuals for Makita DBM230
Summary of Contents for Makita DBM230
- Page 1 Diamant-Kernbohrmaschine Originalbetriebsanleitung Diamond Core Drill Original Instructions Carotteuse diamant à eau Notice originale Carotatrice ad umido Istruzioni originali Taladro Para Broca de Diamante Instrucciones de servicio originales corte húmedo Berbequim com broca de diamante Manual original húmida Diamantkernboor, nat gebruik Oorspronkelijke gebruiksaanwijzing Våddiamantkerneboremaskine Original brugsanvisning...
- Page 2 ENGLISH Icons Warning: general precaution Warning: dangerous voltage Warning: hot surface Tool, drill bit and stand are heavy - caution: risk of squashing Danger of tearing or cutting For your protection the following safety measures should be taken: Wear ear protection Wear safety goggles Wear protective helmet Wear protective gloves...
- Page 3 Equipment characteristics: Wet Diamond Core Drill DBM 230 Rated Voltage: 230 V ~ Rated Power Input: 2500 W Rated Current: 13,5 A Frequency:: 40-60 Hz max. Drilling Diameter: 230 mm Holding fixture: 1¼" UNC Insulation Class: IP Rating: IP 20 Weight according to EPTA Procedure 01/2003: 11,3 kg Interference Suppression:...
- Page 4 Work carefully and with concentration. Keep your work area clean and avoid hazardous situations. Take precautions for the protection of the operator. If the cable is damaged or severed during operations, do not touch the cable, immediately pull the main plug. Never use the tool when the cable is damaged.
- Page 5 Persons under 16 years of age must not operate the tool and persons over 16 and under 18 must only use under close supervision The operator and persons in the vicinity must wear appropriate safety goggles, protective helmet, ear protection, protective gloves and safety shoes during operations.
- Page 6 Power connection The DBM 230 is a protection class I insulated machine. For protection purposes the tool may only be operated with a GFCI. Therefore a GFCI-switch is integrated in the cable for use in a safety plug with ground. ...
- Page 7 Gear shifting The DBM 230 is equipped with a mechanical 3-gears transmission in oil bath. Adjust the rotation speed of the engine to the drill diameter (for details see identification plate). Turn the gear switch to a faster/slower gear until it arrests. Gears must only be shifted when the engine is at stand-still.
- Page 8 Install power lines in such a way that any damage by the drill can be avoided. Make sure to always keep the work area in view and to be able to reach all necessary operating elements and safety installations. Keep other persons away from your work area in order to avoid ...
- Page 9 Screw the quick action clamping screw (D) into the dowel. Install the mount. Fix the washer (E) and finally the fastening nut (F) on the quick action clamping screw (D). Torque the fastening nut with a SW 27 ...
- Page 10 The vacuum pump has to run during the complete operation, it is to be placed in such a way that you can always observe the pressure gauge. It is mandatory to check that the foot plate is firmly affixed before you start drilling.
- Page 11 Overhead drilling You must install a water extracting device. Connect a wet vacuum to the extracting device and switch it on. Open the water supply and ensure that the water reaches the segments before you start drilling. When drilling overhead take special care that no water enters into the ...
- Page 12 Overload Protection In order to protect the operator, the motor and the drill bit, the DBM 230 is equipped with mechanical, electronic and thermal overload protection. Mechanical: If the drill bit is suddenly blocked in the borehole, a slip clutch will disengage the drill bit from the motor. Electronic: An LED is built into the housing in order to alert the operator in case of excessive forward pressure.
- Page 13 After drilling After you have finished drilling: Remove the drill bit from the borehole. Switch the motor off. Use the motor switch and not the GFCI for this purpose. Close the water supply. Removal of the bore core, in case it is stuck in the drill bit. Remove the drill bit from the motor.
- Page 14 In case of malfunctions In case of malfunctions switch the tool off and pull the mains plug. Repairs on the electric parts of the tool may only be performed by an electrical specialist. Troubleshooting Malfunction Possible cause Repair Tool does not - Line voltage - Plug in other electric tool, operate...