LED Indication Using Your RoboVac Important Tips Before Use Preparation Use the Auto-Empty Station Use Your RoboVac with the eufy Clean App Start / Pause Cleaning Select a Cleaning Mode Select a Suction Power Level Use Mopping System Use RoboVac with Amazon Alexa / The Google...
Important Safety Instructions • This device is for indoor use only. • This device is not a toy. Do not sit or stand on this device. Small children and pets should be supervised when this To reduce the risk of injury or damage, keep these instructions device is operating.
Page 4
• Only use attachments recommended or described in this Notice manual. This symbol on the device or its packaging • Do not handle the device or plug with wet hands. indicates: • Ensure that the dust bag and/or filters are correctly in Do not dispose of electrical appliances as unsorted place before use.
Page 5
particular installation. If this equipment does cause interference that may cause undesired operation of the harmful interference to radio or television reception, which device. can be determined by turning the equipment on and off, Declaration of Conformity the user is encouraged to try to correct the interference This product complies with the radio interference by one or more of the following measures: (1) reorient or requirements of the European Community.
About Your RoboVac Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong What's in the Box Trademark Notice • Amazon, Echo, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. • Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.
RoboVac Anatomy E. Suction Inlet Dust Box and Water Tank (2-in-1) A. Top & Side Spot Cleaning Button Recharge Button Auto-Cleaning Start/Pause Button Wi-Fi Status Light Bumper Suction Inlet Suction Inlet Infrared Sensor Main Power Switch (On/Off) Charging Contact Pins (x2) Dust box and water tank (2-in-1) F.
1.02 in / 26 mm as they may cause RoboVac to malfunction. • When you use the Find My Robot function via the eufy Clean app, all three LED indicators are steady blue and a voice prompt is heard.
Preparation Place the auto-empty station on a level surface and against a wall. Remove the foam blocks beside the bumper before use. Install the side brush before use. Install the supplied protective pad under the auto-empty station before using it on a carpet.
• Make sure the power cord is connected to a power outlet and the dust bag is properly installed. • Based on eufy's internal laboratory tests, the dust bag can lock 99.7% of allergens (such as dust, garbage, dust mites, pet dander, etc.) to prevent them from emitting into the air.
Status of Auto-Empty Station LED Indicator Steady white, with 50% Standby brightness To enjoy all the available features, it is recommended to control your RoboVac via the eufy Clean app. Flashing white slowly Working normally Before you start, make sure that: Working abnormally •...
Select a Cleaning Mode • You can also select the cleaning mode via the eufy Clean app. • In the eufy Clean app, RoboVac can be set to return to the auto-empty station automatically if the battery level becomes low. Once recharged, RoboVac will resume cleaning.
Select BoostIQ™ feature In the eufy Clean app, select the BoostIQ™ feature according to your needs. RoboVac will automatically increase suction power if it detects that stronger power is needed to ensure the best clean. BoostIQ™ is ideal for cleaning thicker carpets and hard-to-sweep messes, which will reduce the total cleaning time but increase the noise level.
Page 14
RoboVac three times before mopping. Start cleaning. RoboVac will automatically vacuum and mop. During mopping, you can choose among three water levels via the eufy Clean app. When RoboVac finishes cleaning, remove the mopping module. Open the water inlet cover to fill with water, then close the cover.
To control RoboVac with Amazon Alexa or the Google Assistant: Swivel Wheel Once a month 1. Open the eufy Clean app and find “Smart Integrations” in the top left. 2. Follow the on-screen instructions to complete the setup. Dust Bag...
Page 16
Open and empty the dust box. Rinse the dust box, water tank, and filters thoroughly with water. Remove the filters. • Do not use a brush, hot water, or any detergent to clean the filter. Air-dry the dust box, water tank, and filters completely before next use. You may use another filter if the original one is not dry.
Clean the Rolling Brush Place the filters back into the dust box and the auto-empty station. Pull on the release tabs to unlock the brush guard, as shown. Lift the rolling brush to remove. Clean the rolling brush with the cleaning tool. Reinstall the rolling brush by inserting the fixed protruding end first.
Clean the Side Brush Replace the Side Brush Foreign substances, such as hair, can easily get tangled in the side brush, so it is best to The side brush may become bent or damaged after being used for a period of time. clean it regularly.
• Clean the path tracking sensor with a soft, dry cloth. Pull out the swivel wheel with a tool (such as a screwdriver). Clean any hair or debris wrapped around the wheel or entangled inside the wheel cavity. Reinstall the wheel and push it in until it clicks into place. •...
Replace the Dust Bag Discard the used dust bag. Lift open the top cover. Install a new dust bag. Remove the dust bag. Press down to close the top cover. 36 EN EN 37...
The solutions below are for general questions. If your problem persists, visit www. • Do not disassemble the auto-empty station by yourself to avoid the risk of eufylife.com, go to the eufy Clean app, or contact support@eufylife.com for help. electric shock.
Clean App. occurred. • Make sure you have an eufy Clean account and have connected to RoboVac. • Make sure you are using correct Alexa voice- Error 7: Wheel Wheels may be suspended in air.
Specifications Voice Prompt Cause and Solution Error 21: Auto-empty Auto-empty station is blocked by obstacles, clear any station blocked by Input 0.6A obstacles around the auto-empty station and try again. surrounding obstacles. Battery Voltage 14.4 V Power Consumption • Open the battery compartment and check whether the 14.4V battery is connected and restart the device.
Need help?
Do you have a question about the Clean G40 Hybrid+ and is the answer not in the manual?
Questions and answers