MERITECH CleanTech 2000S Installation And Operation Manual
Automated hand cleansing system with the sole-clean pan
Hide thumbs
Also See for CleanTech 2000S:
- Installation and operation manual (13 pages) ,
- Installation and operation manual (35 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MERITECH CleanTech 2000S
Summary of Contents for MERITECH CleanTech 2000S
- Page 1 CleanTech 2000S Sole-Clean Pan INSTALLATION AND OPERATION MANUAL...
- Page 2 E-mail: service@meritech.com WARNING: The performance and effectiveness of CleanTech® systems have been extensively tested when using solutions provided by Meritech Systems, LLC. Satisfactory performance or effectiveness cannot be guaranteed when other solutions are used. FAILURE TO USE MERITECH SYSTEMS, LLC SUPPLIED...
-
Page 3: Table Of Contents
MERITECH SYSTEMS, LLC CleanTech 2000S Sole-Clean Pan Installation and Operation Manual Description Page # Table of Contents Introduction Overview Facility Installation Instructions / Requirements 6 - 8 First Time Start Up / Operation Cycle Time / Calibration System Cleaning Contacting Meritech... -
Page 4: Introduction
The CleanTech 2000S w/ Sole-Clean Pan has a 23" wide X 42" deep footprint, and the accompanying cart has a 16” wide by 18” deep footprint. The system will hook-up to your existing, standard hot/cold water lines and wall drain for the handwasher. -
Page 5: Overview
Overview The Meritech CleanTech 2000S system with the Sole-Clean Pan provides a means of washing hands and sanitizing footwear at the same time for your employees while maintaining a low moisture environment that traditional boot dips do not allow. This is possible through the use of the Sanifect D2 alcohol-based sanitizer, which is quick to evaporate and prevents excessive moisture build-up and tracking. -
Page 6: Facility Installation Instructions/Requirements
Facility Installation Instructions/Requirements The CleanTech 2000S system should be installed per the instructions within its separate installation / operation manual. This manual gives detailed instructions on the installation, operation, & cleaning of the Sole-Clean Pan. Do not hardwire the system electrical cord without having a way to disconnect the system from the electrical source for future serviceability of the system. - Page 7 3. Make certain that the pan is sitting level and does not rock. 4. Place the three mats into the pan, ensuring that they are in the correct order from bottom to top: black bubble mat, grey absorptive mat (with soft side up), red foot placement mat (with grip knobs upward).
- Page 8 IF YOU SHOULD EXPERIENCE ANY DIFFICULTY OR ARE UNSURE ABOUT THE INSTALLATION PROCEDURE, WE ENCOURAGE YOU TO CONSULT IMMEDIATELY WITH MERITECH. 720 Corporate Circle, Suite K Golden, CO 80401 USA Phone: (800) 932-7707 Fax: (303) 790-4859 www.meritech.com...
-
Page 9: First Time Start Up / Operation
First Time Start Up & Operation Once the CleanTech 2000S system is installed with the Sole-Clean and is fully functional, follow the steps below to prime the pan for the first time. 1. Locate the “Prime Sanifect D2” button on the face of the Sole-Clean system. -
Page 10: Cycle Time / Calibration
Meritech. Cycle Time / Calibration To adjust cycle time and calibration of the system, please contact Meritech customer service for assistance. Please refer to “Contacting Meritech” in this manual. Sanitizing Fluid is Empty – How to Refill 1. -
Page 11: Contacting Meritech
THE CleanTech FAMILY OF SYSTEMS HAS BEEN DESIGNED TO OPERATE SPECIFICALLY WITH THE SOLUTIONS PROVIDED OR APPROVED BY MERITECH. THEY ARE OF A SPECIFIC CONCENTRATION AND VISCOSITY. WE CANNOT GUARANTEE SATISFACTORY PERFORMANCE NOR WARRANTY THE SYSTEM IF THE CONTAINERS ARE FILLED WITH A DIFFERENT SOLUTION.
Need help?
Do you have a question about the CleanTech 2000S and is the answer not in the manual?
Questions and answers