Advertisement
Quick Links
RX2AP
TWO OUTPUTS RADIO RECEIVER
[AN]
THE INSTALLER HAS TO FOLLOW REGULATIONS. INTERVENTIONS MADE BY NOT AUTHORIZED STAFF CAN DAMAGE THE DEVICE.
THE PRODUCER IS NOT RESPONSIBLE IN CASE OF IMPROPER USE OR WRONG INSTALLATION.
DO NOT INSTALL THE RECEIVER IN DUMP PLACES OR EXPOSED AT HIGH/LOW TEMPERATURES OR INCLEMENCY OF THE WEATHER.
FOR MORE SAFETY, INSTALL THE RECEIVER IN A PLACE PROTECTED BY AN ALARM DETECTOR.
RX2AP is a receiver that can store up to 10 radio codes (auto-learning) combined to 2 independent outputs (5 radio codes each): the outputs are dry-contact relay type.
It is possible to learn the radio codes of sensors, remote controls or special transmitters (TSR) for control panels.
Matching scheme of Radio
Zones with Relay Outputs:
This device allow a simple interface between wired control panels and wireless sensors or remote controls.
INDEX
1.
RESET ................................................................................................................................................................................................................................................ 1
2.
TECHNICAL ........................................................................................................................................................................................................................................ 2
3.
LEARNING ......................................................................................................................................................................................................................................... 2
4.
"SENSORS + REMOTE CONTROLS" MODE DIP1 = OFF | DIP3 = OFF | DIP4 = OFF.............................................................................................................................. 3
5.
"REMOTE CONTROLS" MODE DIP1 = OFF | DIP3 = OFF | DIP4 = ON ................................................................................................................................................. 3
6.
"LIGHT TIMER" MODE DIP1 = OFF | DIP3 = ON | DIP4 = OFF ............................................................................................................................................................ 4
7.
USE OF THE TSR TRANSMITTER DIP1 = OFF | DIP3 = OFF | DIP4 = OFF .............................................................................................................................................. 4
1.
RESET
The following procedure bring back the receiver to factory settings. It is necessary to run the reset before start programming and use the device.
1.
Remove power to the receiver (wait about 1 minute the circuit discharges)
2.
Hold down the P button while powering the receiver
3.
After about 5 seconds the receiver emits three quick "beep" followed by one long one
4.
Release the P button. The reset is complete.
Installation and use manual
Radio Zone A-1
Radio Zone A-2
Radio Zone A-3
Radio Zone A-4
Radio Zone A-5
This manual is subject to modification without advice
MADE IN ITALY
RELAY A
15.10-M:4.1-H:x.x-F:F9D0
Radio Zone B-1
Radio Zone B-2
Radio Zone B-3
Radio Zone B-4
Radio Zone B-5
RELAY B
Advertisement
Related Manuals for Duevi RX2AP
Summary of Contents for Duevi RX2AP
- Page 1 FOR MORE SAFETY, INSTALL THE RECEIVER IN A PLACE PROTECTED BY AN ALARM DETECTOR. RX2AP is a receiver that can store up to 10 radio codes (auto-learning) combined to 2 independent outputs (5 radio codes each): the outputs are dry-contact relay type.
- Page 2 TECHNICAL RELAY OUTPUTS 2 alarm relays (mono-stable or bi-stable working modes) MAX: 24 V / 500 mA SIGNALLING Buzzer on board for operation feedback (not excludible) 4 internal LEDs for operation feedback (2 LEDs for relay outputs state, 2 LEDs for Radio Zones management) RADIO RECEIVER Working frequency: 433.92 MHz –...
- Page 3 To learn a sensor/remote control/TSR in selected memory space: hold down the P button for 3 seconds the LED_X or LED_O light on (depending on which one was already on): the receiver is now waiting make the sensor * (only AN code, see sensor manual), the remote control or the TSR transmitter (only ...
- Page 4 “LIGHT TIMER” MODE DIP1 = OFF | DIP3 = ON | DIP4 = OFF This mode (DIP3 = ON) set the receiver to maintain active the Relay outputs for 3 minutes (useful as light timer) when it is received a radio code from a remote control, a sensor or the “alarm”...
Need help?
Do you have a question about the RX2AP and is the answer not in the manual?
Questions and answers