Supplied Accessories - PCB Piezotronics IMI SENSORS Swiveler ICP 607A01 Installation And Operating Manual

Model Number
607A01
Performance
Sensitivity(± 15 %)
Measurement Range
Frequency Range(± 3 dB)
Resonant Frequency
Broadband Resolution(1 to 10,000 Hz)
Non-Linearity
Transverse Sensitivity
Environmental
Overload Limit(Shock)
Temperature Range
Temperature Response
Enclosure Rating
Electrical
Settling Time(within 1% of bias)
Discharge Time Constant
Excitation Voltage
Constant Current Excitation
Output Impedance
Output Bias Voltage
Spectral Noise(10 Hz)
Spectral Noise(100 Hz)
Spectral Noise(1 kHz)
Electrical Isolation(Case)
Physical
Size (Hex x Height)
Weight
Mounting
Mounting Thread
Mounting Torque(Stud)
Mounting Torque(hex nut)
Sensing Element
Sensing Geometry
Housing Material
Sealing
Electrical Connector
Electrical Connection Position
[6]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
®
ICP is a registered trademark of PCB Group, Inc.
SWIVELER® INDUSTRIAL ICP® ACCELEROMETER
ENGLISH SI
100 mV/g 10.2 mV/(m/s²)
± 50 g ± 490 m/s²
30 to 600,000 cpm 0.5 to 10,000 Hz
1080 kcpm 18 kHz
350 µg
3434 µm/sec
± 1 % ± 1 %
≤ 7 % ≤ 7 %
5000 g pk 49,050 m/s² pk
-65 to +250 °F -54 to +121 °C
See Graph See Graph
IP68 IP68
≤ 2.0 sec ≤ 2.0 sec
≥ 0.3 sec ≥ 0.3 sec
18 to 28 VDC 18 to 28 VDC
2 to 20 mA 2 to 20 mA
<150 Ohm <150 Ohm
8 to 12 VDC 8 to 12 VDC
8 µg/√Hz 2
78.5 (µm/sec )/√Hz
5 µg/√Hz 2
49.1 (µm/sec )/√Hz
4 µg/√Hz 2
39.2 (µm/sec )/√Hz
8 8
>10 Ohm >10 Ohm
7/8 in x 1.23 in 22 mm x 31.2 mm
3.7 oz 105 gm
Stud Stud
1/4-28 Male 1/4-28 Male
3 to 4 ft-lb 4.1 to 5.4 Nm
2 to 3 ft-lb 2.7 to 4.1 Nm
Ceramic Ceramic
Shear Shear
Stainless Steel Stainless Steel
Welded Hermetic Welded Hermetic
2-Pin MIL-C-5015 2-Pin MIL-C-5015
Side Side
[2]
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
[1]
- Hazardous Area Approval- contact factory for specific approvals
EX
[1]
2
Hazardous Area Approval
[3]
Hazardous Area Approval
Hazardous Area Approval
[1] Hazardous Area Approval
Hazardous Area Approval
- Metric Mount
M
Supplied Accessory : Model M080A163A (1) replaces Model 080A162
- Temperature Output
TO
Temperature Output Range
[1]
Temperature Scale Factor
[1]
Electrical Connector
[1]
Electrical Connections(Pin A)
Electrical Connections(Pin B)
Electrical Connections(Pin C)
[4][5]
NOTES:
[1]Typical.
[2]Conversion Factor 1g = 9.81 m/s².
[3]Zero-based, least-squares, straight line method.
[4]1/8" hex Allen key required for English version, 3mm hex Allen key required for metric version.
[5]Stud torque must exceed sensor hex nut torque to ensure proper dismantling.
[6]See PCB Declaration of Conformance PS023 for details.

SUPPLIED ACCESSORIES:

Model 080A162 Mounting Stud (1)
Model ICS-2 NIST-traceable single-axis single-point amplitude response calibration at 6000
cpm (100 Hz) (1)
Entered: AP Engineer: DK
Date: 10/10/2014 Date: 10/10/2014
3425 Walden Avenue, Depew, NY 14043
Revision: F
ECN #: 43341
OPTIONAL VERSIONS
Ex ia IIC T4, AExia IIC, T4 Ex ia IIC T4, AExia IIC, T4
EEx nL IIC T4, -40°C≤Ta≤121° EEx nL IIC T4, -40°C≤Ta≤121°
C, II 1 G C, II 1 G
Cl I, Div I, Groups A, B, C, D; Cl Cl I, Div I, Groups A, B, C, D; Cl
II, Div I, Groups E, F, G; Cl III, II, Div I, Groups E, F, G; Cl III,
Div I Div I
Cl I, Div 2, Groups A, B, C, D; Cl I, Div 2, Groups A, B, C, D;
ExnL IIC T4, AExnA IIC T4 ExnL IIC T4, AExnA IIC T4
EEx nL IIC T4, -40°C≤Ta≤121° EEx nL IIC T4, -40°C≤Ta≤121°
C, II 3 G C, II 3 G
+36 to +250 °F +2 to +121 °C
5.56 mV/°F + 32 +10 mV/°C
3-Pin MIL-C-5015 3-Pin MIL-C-5015
Acceleration Output Acceleration Output
Ground Ground
Temperature Output Temperature Output
Sales: EGY Approved: BAM
Date: 10/10/2014 Date: 10/10/2014
Phone: 800-959-4464
Fax: 716-684-3823
E-Mail: imi@pcb.com
Spec Number:
13832