DeWalt DWE575 Manual page 14

English
Checking the Lower Guard (Fig. A)
1. Turn tool off and disconnect from power supply.
2. Rotate the lower guard lever (Fig. A,
closed position to the fully open position.
3. Release the lever and observe the guard
fully closed position.
The tool should be serviced by a qualified service center if it:
• fails to return to the fully closed position,
• moves intermittently or slowly, or
• contacts the blade or any part of the tool in all angles and
depth of cut.
Blades

WARNING: To minimize the risk of eye injury, always
use eye protection. Carbide is a hard but brittle material.
Foreign objects in the workpiece such as wire or nails
can cause tips to crack or break. Only operate saw when
proper saw blade guard is in place. Mount blade securely
in proper rotation before using, and always use a clean,
sharp blade.
Diameter
184 mm
184 mm
184 mm
If you need assistance regarding blades, please contact your
local D WALT dealer.
e
Kickback
Kickback is a sudden reaction to a pinched, bound or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator. When the blade is pinched or
bound tightly by the kerf closing down, the blade stalls and the
motor reaction drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth
at the back edge of the blade can dig into the top surface of the
material causing the blade to climb out of the kerf and jump
back toward the operator.
Kickback is more likely to occur when any of the following
conditions exists.
1. iMPROPER WORKPiECE sUPPORT
a. Sagging or improper lifting of the cut off piece can cause
pinching of the blade and lead to kickback (Fig. P).
b. Cutting through material supported at the outer ends
only can cause kickback. As the material weakens it sags,
closing down the kerf and pinching the blade (Fig. P).
c. Cutting off a cantilevered or overhanging piece of
material from the bottom up in a vertical direction
can cause kickback. The falling cut off piece can pinch
the blade.
d. Cutting off long narrow strips can cause kickback. The
cut off strip can sag or twist closing the kerf and pinching
the blade.
e. Snagging the lower guard on a surface below the
material being cut momentarily reduces operator control.
12
) from the fully
12
10 return to the
Teeth Application
18 Fast rip
24 Rip
36 General purpose
The saw can lift partially out of the cut increasing the
chance of blade twist.
2. iMPROPER DEPTh OF CUT sETTing On sAW
To make the most efficient cut, the blade should protrude
only far enough to expose a tooth as shown in Figure H. This
allows the shoe to support the blade and minimizes twisting
and pinching in the material. See the section titled Depth of
Cut Adjustment.
3. BlADE TWisTing (MisAlignMEnT in CUT)
a. Pushing harder to cut can cause the blade to twist.
b. Trying to turn the saw in the cut (trying to get back on
the marked line) can cause blade twist.
c. Overreaching or operating the saw with poor body
control (out of balance), can result in twisting the blade.
d. Changing hand grip or body position while cutting can
result in blade twist.
e. Backing up the saw to clear blade can lead to twist.
4. UsE OF DUll OR DiRTY BlADEs
Dull blades cause increased loading of the saw. To
compensate, an operator will usually push harder which
further loads the unit and promotes twisting of the blade
in the kerf. Worn blades may also have insufficient body
clearance which increases the chance of binding and
increased loading.
5. REsTARTing A CUT WiTh ThE BlADE TEETh JAMMED
AgAinsT ThE MATERiAl
The saw should be brought up to full operating speed
before starting a cut or restarting a cut after the unit has
been stopped with the blade in the kerf. Failure to do so can
cause stalling and kickback.
Any other conditions which could result in pinching, binding,
twisting, or misalignment of the blade could cause kickback.
Refer to the sections Additional Specific Safety Rules for
Circular Saws and Blades for procedures and techniques that
will minimize the occurrence of kickback.
Depth of Cut Adjustment (Fig. F–H)
1. Raise the depth adjustment lever
2. To obtain the correct depth of cut, align the appropriate
mark on the depth adjustment strap
the upper blade guard.
3. Tighten the depth adjustment lever.
4. For the most efficient cutting action using a carbide tipped
saw blade, set the depth adjustment so that about one half
of a tooth projects below the surface of the wood to be cut.
5. A method of checking for the correct cutting depth is
shown in Figure H. Lay a piece of the material you plan to
cut along the side of the blade, as shown in the figure, and
observe how much tooth projects beyond the material.
Adjusting Depth adjustment lever (Fig. G)
It may be desirable to adjust the depth adjustment lever
may loosen in time and hit the base plate before tighten ing.
To Tighten the lever:
1. Hold depth adjustment lever
locknut 20 .
17 to loosen.
with notch
19 18
17
17 and loosen the
on
. It