Table of Contents
Advertisement
Quick Links
1-800-4-D
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DWE574, DWE575, DWE575SB
7-1/4" (184 mm) Circular Saws
Scies circulaires de 184 mm (7-1/4 po)
Sierras circulares de 184 mm (7-1/4")
FINAL PRINT SIZE: 8.5 x 5.5"
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
WALT • www.dewalt.com
e
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
Advertisement
Table of Contents
Related Manuals for DeWalt DWE574
Summary of Contents for DeWalt DWE574
- Page 1 GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE GUIDE D'UTILISATION USAR EL PRODUCTO. MANUAL DE INSTRUCCIONES DWE574, DWE575, DWE575SB 7-1/4" (184 mm) Circular Saws Scies circulaires de 184 mm (7-1/4 po) Sierras circulares de 184 mm (7-1/4") FINAL PRINT SIZE: 8.5 x 5.5"...
-
Page 2: Definitions: Safety Guidelines
The term “power tool” in the warnings refers to your mains-operated Definitions: Safety Guidelines (corded) power tool or battery-operated (cordless) power tool. The definitions below describe the level of severity for 1) WORK AREA SAFETY each signal word. Please read the manual and pay a) Keep work area clean and well lit. -
Page 3: Personal Safety
f) If operating a power tool in a damp location is unavoidable, 4) POWER TOOL USE AND CARE use a ground fault circuit interrupter (GFCI) protected a) Do not force the power tool. Use the correct power tool supply. Use of a GFCI reduces the risk of electric shock. for your application. -
Page 4: Cutting Procedures
5) SERVICE h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your a) Have your power tool serviced by a qualified repair saw, for optimum performance and safety of operation. person using only identical replacement parts. -
Page 5: Lower Guard Function
c) When restarting a saw in the workpiece, center the Raise lower guard by retracting handle and as soon saw blade in the kerf and check that saw teeth are not as blade enters the material, the lower guard must be engaged into the material. - Page 6 • Always be sure all components are mounted properly and securely Minimum Gauge for Cord Sets before using tool. Volts Total Length of Cord in Feet (meters) • Always handle the saw blade with care when mounting or Ampere Rating 120V 25 (7.6) 50 (15.2)
-
Page 7: Components (Fig. 1)
Motor Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on Be sure your power supply agrees with the nameplate marking. the skin may promote absorption of harmful chemicals. Voltage decrease of more than 10% will cause loss of power and WARNING: Use of this tool can generate and/or disperse dust, overheating. -
Page 8: Intended Use
INTENDED USE direction of the rotation arrow on the saw blade and the teeth must point in the same direction as the direction of rotation arrow on the These heavy-duty circular saws are designed for professional wood saw). Do not assume that the printing on the blade will always be cutting applications. -
Page 9: Lower Blade Guard
assure product safety and reliability, repair, maintenance and TO REPLACE THE BLADE (FIG. 2, 4, 5) adjustment should be performed by an authorized service 1. To loosen the blade clamping screw (J), depress the blade lock center or other qualified service organization, always using (C) and turn the saw spindle with the blade wrench (O), stored identical replacement parts. - Page 10 (U). The full range of bevel adjustment for the DWE574 is 0 to 50 degrees 3. For the most efficient cutting action using a carbide tipped saw and for the DWE575 and blade, set the depth adjustment so that about one half of a tooth...
-
Page 11: Operation
Kerf Indicator (Fig. 10) Proper Hand Position (Fig. 12) The front of the saw foot plate has a kerf indicator for vertical and bevel WARNING: To reduce the risk of FIG. 12 cutting. This indicator enables you to guide the saw along cutting lines serious personal injury, ALWAYS penciled on the material being cut. - Page 12 most important—down. The saw cuts upward, so any splintering will be cut off the end of a board. Always clamp work. Don’t try to hold short on the work face that is up when you saw it. pieces by hand! Remember to support cantilevered and overhanging material.
- Page 13 3. Using the lower guard lever, retract lower blade guard to an As you finish a cut, release the trigger and allow the blade to stop upward position. Lower rear of foot plate until blade teeth almost before lifting the saw from the work. As you lift the saw, the spring- touch cutting line.
-
Page 14: Maintenance
B. Cutting through material supported at the outer ends only can C. Pressure treated lumber (material treated with preservatives or cause kickback. As the material weakens it sags, closing down anti-rot chemicals) the kerf and pinching the blade. 5. USE OF DULL OR DIRTY BLADES C. -
Page 15: Foot Plate Adjustment
Cleaning Brushes (Fig. 19) WARNING: Blow dirt and dust out of all air vents with clean, dry air WARNING: To reduce the risk of injury, turn unit off and at least once a week. To minimize the risk of eye injury, always wear disconnect it from power source before installing and removing ANSI Z87.1 approved eye protection when performing this. - Page 16 Your foot plate has been factory set to assure that the blade is 2. Adjust the bevel adjustment lever by rotating it in the desired perpendicular to the foot plate. If after extended use you need to direction about 1/8 of a revolution. re-align the blade, follow the directions below: 3.
-
Page 17: Three Year Limited Warranty
Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call company or see website for warranty information. 1-800-4-D WALT (1-800-433-9258) or visit our website www.dewalt. FREE WARNING LABEL REPLACEMENT: If your warning labels com. become illegible or are missing, call 1-800-4-D WALT (1-800-433- DO NOT USE WATER FEED ATTACHMENTS WITH THIS SAW. - Page 18 WALT Industrial Tool Co., 701 Joppa Road, Towson, MD 21286 (JUN15) Part No. N444623 DWE574, DWE575, DWE575SB Copyright © 2011, 2015 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill;...