Maxeon SunPower Performance SPR-P6-555-UPP Safety And Installation Instructions Manual page 6

Appendix: Mounting Loads and Configurations
SunPower Performance 5/6 Bifacial Solar Panel
(SPR-P5-XXX-UPP, SPR-P6-XXX-UPP)
0
TOP CLAMPS
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on Front View
Long Side Moun ng,
Rails Perpedincular to
Moun ng Frame
Long Side Moun ng,
Point Supported
Long Side Moun ng,
Rails Parallel to
Moun ng Frame
Short Side Moun ng,
Point Supported
(End Mount)
Short Side Moun ng,
Point Supported
with Rail
(End Mount)
Short Side Moun ng,
Rails Parallel to
Moun ng Frame
(End Mount)
Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
par es, unless there is a formal authoriza on by Maxeon.
2 Test loads are for informa on purposes only, design loads should be considered for the project design.
© 2022 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in these instructions are subject to change without notice.
1232.77 [48.53in]
546 646
[21.49]
[25.43]
A
1100 mm [43.31in]
1400 mm [55.12in]
2384 mm [93.86in]
Measurement Tolerances are +/-3 mm for the Length and Width of the Module.
Moun ng Zone
Test Load
Loca ons
Downward/Upward Downward/Upward
(distance from corner
Back View
(Pa)
in mm)
+2400/-1200
50 - 546 +1600/-800
+3600/-1600
546 - 646 +5400/-2400
646 - 1042 +2400/-2000 +1600/-1333
+1800/-1800
50 - 100 +1200/-1200
+3000/-2400
546 - 646
50 - 546 +2400/-1200
0 - 323
+1400/-1400
0 - 323 +3600/-2400
0 - 323
+1400/-1400
Safety and Installation Instructions ‐ Document 539821 Rev B
1088.77 [42.86in]
1042
1042
[41.02] [41.02]
B
400 mm
[15.74in]
A - SLOT Holes (8X 14mm (L) x 9mm (W), R3.5mm)
B - Moun ng Holes (4X 10mm (L) x 7mm (W), R6.8mm)
C - Ground Holes (4X Ø 4.2mm)
Design Load
(Pa)
SIDE FRAME PROFILE
+2000/-1600
35mm [1.38]
+1600/-800
BOLTS
+933/-933
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on Front View
Long Side Moun ng,
Rails Perpedincular to
+2400/-1600
Moun ng Frame
Center Moun ng
+933/-933
(1x Portrait Tracker)
3 Minimum of 24mm in diameter washer size is required.
4 Rails must not be under the junc on box.
MAXEON SOLAR TECHNOLOGIES, LTD.
0
646 546
[25.43] [21.49]
C
GEN 4.3 FRAME PROFILE
END FRAME PROFILE
16 mm
[0.630]
Moun ng Zone
Test Load
Loca ons
(distance from corner
Downward/Upward
Back View
(Pa)
in mm)
1400mm Holes +5400/-2400
+5400/-2400
1100mm Holes
400mm Holes +2400/-2000
+1800/-1800
400mm Holes
Design Load
Downward/Upward
(Pa)
+3600/-1600
+3600/-1600
+1600/-1333
+1200/-1200
Page | 6