Related Manuals for Oliver 1308-N
Summary of Contents for Oliver 1308-N
- Page 1 Walker, Michigan, U.S.A. 49534-7564 USER’S OPERATING AND INSTRUCTION MANUAL MODEL 1308-N & 1308-C HEAT SEALER 1308S20000CV1...
-
Page 2: Table Of Contents
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 INDEX Section Description Document No. Page No. DESCRIPTION/SPECIFICATIONS----------------------------1308S20013 ------------------------- 1-1 Description------------------------------------------------------------------------------------------------------- 1-1 Specifications------------------------------------------------------------------------------------------------------ 1-1 GENERAL SAFETY INSTRUCTIONS-------------------------1308S20014-------------------------- 2-1 Lockout-Tag out-------------------------------------------------------------------------------------------- 2-1 SETUP AND OPERATION GUIDE-----------------------------1308S20036--------------- 4-1 TO 4-6... - Page 3 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 4: Description/Specifications
DESCRIPTION/SPECIFICATIONS Description The Oliver Model 1308 Heat Sealer is designed and manufactured to ensure a user friendly operation of producing film lidded trays with a cost effective approach. The manually operated machine operates with either a 120 or 230 V.A.C. outlet. The machine was designed to be compact to limit the amount of table space needed to operate. - Page 5 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 6: General Safety Instructions
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 GENERAL SAFETY INSTRUCTIONS WARNING IT IS ESSENTIAL THAT ALL OPERATORS AND MAINTENANCE PERSONNEL OBSERVE THE FOLLOWING SAFETY PRECAUTIONS. IMPROPER INSTALLATION, MAINTENANCE, OR OPERATION OF THIS EQUIPMENT MAY CAUSE SERIOUS INJURY. -
Page 7: Setup And Operation Guide
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 1308 SETUP AND OPERATION GUIDE Shipping carton Remove the 1308 Open carton as shown Remove parts and packing Unit. TWO PERSON ... - Page 8 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 Locate the two counterweight Install plastic knob and tighten Install holder holders and plastic knobs Install plastic knob and tighten ...
- Page 9 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 Remove zip-ties securing For models with a switch, Handle shown in the handle to base and lift install power cord plug as upright position handle...
- Page 10 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 Pull the handle down all the Lift handle t o the Using both hands pull way to this position and hold upright position the handle down...
- Page 11 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 BASIC MACHINE COMPONENTS AND SET UP Before proceeding further, take a moment to familiarize yourself with the identification of the machine components as shown in the illustration below.
- Page 12 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 SET UP CONTIUED NOTE: FILM SUPPLIED BY OLIVER PRODUCTS COMPANY IS WOUND WITH THE ADHEASIVE SIDE IN. FEED FILM FROM THE TOP OF THE ROLL AS SHOWN. 1308S20016...
-
Page 13: Operating Procedures
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 OPERATING PROCEDURES 1. CAUTION – To provide continued protection against risk of electric shock, connect only to properly grounded outlets only. Avoid the use of extension cords. -
Page 14: Adjustment And Quality
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 ADJUSTMENT AND QUALITY Your OLIVER Model 1308 was tested at the factory using Oliver trays and film. NOTE THE TEMPERATURE CANNOT BE ADJUSTED BY THE OPERATOR The heater platen temperature is factory set at approximately 300°F (Approx. - Page 15 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 16: Cleaning And Maintenance
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 CLEANING AND MAINTENANCE NOTE • These cleaning recommendations are not meant to replace plant standard manufacturing procedures or regulatory requirements. • Do not submerge unit in water. Do not wash down. -
Page 17: Cleaning And Maintenance Continued
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 CLEANING AND MAINTENANCE CONTINUED CLEANING PROCEDURE - MACHINE FRAME AND BASE NOTE: SEE HEATER PLATEN AND FILM CUTTER CLEANING SECTIONS FOR SPECIFIC GUIDANCE ON THEIR CLEANING PROCEDURES 1. - Page 18 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 CLEANING AND MAINTENANCE CONTINUED REPLACING AND CHECKING GASKETS • If there are any gouges, cuts or gaps in the gasket, the gasket will have to be replaced.
-
Page 19: Trouble Shooting
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 TROUBLE SHOOTING SYMPTOM CORRECTIVE ACTION Verify that the platen is heated and is at the correct Poor seal quality temperature (approximately 300F/150°C) Check to see if the platen is dirty... - Page 20 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319...
-
Page 21: Wiring Diagram
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 WIRING DIAGRAM 1-60-120V REF. W/D 1308C12002 1-60-230V REF. W/D 1308C12000 REV. 4-27-12 1308S20021... -
Page 22: 1308 Heat Sealer
Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 MODEL 1308 HEAT SEALER Rev 7/14/20 1308S20022 10-1... - Page 23 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 MODEL 1308 HEAT SEALER PARTS LISTS ITEM NO PART DESCRIPTION PART NUMBER______QTY Base 1308-0015-301 Bumper-Rubber 5902-0035 PIN-DOWEL 1/4X3/4" STST 5835-6475 Tube-Aluminum 7/8” O.D. 4639-1414-1116 Bearing-Roll End...
- Page 24 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 PARTS LIST CONTINUED ITEM NO PART DESCRIPTION PART NUMBER______QTY Shaft-Mid Pivot 1308-0002 PLUG-HOLE DOME WHITE 3/16" 5769-3000 Weight-Counter 1308-0042-1 Counter Weight 1308-0065 1908-0262 COVER-CLAMP 1308-0500-1...
- Page 25 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 PARTS LIST CONTINUED ITEM NO PART DESCRIPTION PART NUMBER______QTY Bar-Pusher 1308-0057 Bolt-Carriage ½-13 x 4-1/2” 5804-1722 NUT-ACORN STD 1/2"-13 5831-8100 NUT-HEX FULL 1/2-13 5832-0524 WASHER-1/2" SPRING LOCK 5851-9011 WASHER-7/16"...
- Page 26 ** Cushions differ from tray carrier to tray carrier. The cushion that is used is determined by the engineer during the design process. FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 Rev 9/6/22 1308S20022...
- Page 27 Oliver Packaging & Equipment Company y 3236 Wilson Drive NW, Walker, MI 49534 (800) 253-3893 MODEL 1308-C ELECTRICAL BOX MODEL 1308-N ELECTRICAL BOX PART DESCRIPTION ITEM NO PART NUMBER______QTY Assembly- Cord & Plug 6 FT (US MODEL) 5765-8374 Assembly- Cord & Plug 2 M (AU MODEL) 5765-8375 Assembly- Cord &...
- Page 28 Oliver Packaging & Equipment Company warrants that if any part of the equipment (other than a part not manufactured by Oliver Packaging & Equipment) proves to be defective (as defined below) within one year after shipment, and if Buyer returns the defective part to Oliver Packaging &...
- Page 29 4. The service dealer will then complete an invoice and send it to the Customer Service Department at Oliver Packaging & Equipment Company. 5. The Customer Service Manager of Oliver Packaging & Equipment Company will review the invoice and returned parts, if applicable, and approve for payment.
- Page 30 This policy applies to all parts returned to the factory whether for warranted credit, replacement, repair or re-stocking. Oliver Packaging & Equipment Company requires that the customer obtain a Return Material Authorization (RMA) number before returning any part. This number should appear on the shipping label and inside the shipping carton as well.
Need help?
Do you have a question about the 1308-N and is the answer not in the manual?
Questions and answers