Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email:
CustomerExperience@belnick.com
ZG-021-WH-GG / ZG-021-GY-GG
Thank you for your purchase!
TV Stand
| Phone: 866-552-2810
Advertisement
Related Manuals for Flash Furniture ZG-021-WH-GG
Summary of Contents for Flash Furniture ZG-021-WH-GG
- Page 1 To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed. Customer Service Email: CustomerExperience@belnick.com | Phone: 866-552-2810 ZG-021-WH-GG / ZG-021-GY-GG...
- Page 2 Have a Question/Concern? Quality products and first-class customer service are the cornerstone of long-lasting consumer relationships. We strive toward excellence in all we do and want you to be completely satisfied with your purchase. Please contact our exceptional Customer Experience Agents at the email address or phone number shown below to assist you with any product questions or issues before requesting a return.
- Page 4 Components - Panels Please check you have all the panels listed below 2.) Left Rear Leg X 1 3.) Right Front Leg X 1 4.) Right Rear Leg X 1 1.) Left Front Leg X 1 7.) Bottom Panel X 1 5.) Left Side Panel X 1 6.) Right Side Panel X 1 8.) Bottom Trim X 1...
- Page 5 Components - Fittings Please check you have all the panels listed below Note: The quantitie below are the correcet amount to complete the assembly. In some cases more fittings may be supplied than are required. -==rt® � Male Camlock x 26 Female Camlock x 26 Wood Dowel x 32 cmm: m uc!@...
- Page 7 Rear Right Leg Top Panel Front Right Leg Right Right Rear Side Panel Panel Right Center Panel Rear Center Right Shelf Panel Left Center Panel Center Shelf Left Rear Panel Bottom Panel Left Side Left Shelf Panel Rear Left Leg Right Door Front Left Leg Left Door...
- Page 8 Insert (12) Male Camlocks (Part A) into the Front and Rear Legs (Parts 1, 2, 3, & 4) as shown. Tighten with a Phillips Screwdriver. Male Camlock NOTE: Ensure Phillips grooves on back Screwdriver legs face inward and towards each other. Rear Left Leg Front Right Leg Front Left Leg...
- Page 9 Insert (8) Female Camlocks into the Left and Right Side Panels as shown then insert the Male Camlocks on the Legs into the Female Camlocks then turn clockwise to tighten using a Phillips Screwdriver. Female Camlocks Right Side Left Side Panel Panel Left Rear Leg...
- Page 10 Attach (2) Middle Support Legs (Part 9) to the underside of the Bottom Panel (Part 7) using (2) 6*50mm Screws (Part E). Tighten using Allen Wrench (Part F). Allen Wrench 6*50mm Screw Bottom Panel Attach Bottom Trim (Part 8) to the underside of the Bottom Panel (Part 7) using (2) 4*45mm Screws.
- Page 11 Insert (4) Wood Dowels (Part C) into the Left Center Panel (Part 10) and the Right Center Panel (Part 11). Left Center Panel Right Center Panel Insert Left and Right Center Panels into the top side of the Bottom Panel (Part 7) and secure using (4) 6*50mm Screws (Part E).
- Page 12 Insert (2) Wood Dowels (Part C) into the Slide Rail (Part 12). Slide Rail Wood Dowel Insert (4) Female Camlocks into the right side of the Slide Rail, Bottom Panel, and Bottom Trim as shown. Insert Male Camlocks into the Female Camlocks and tighten using a Phillips Screwdriver.
- Page 13 Insert (4) Female Camlocks into the left side of the Slide Rail, Bottom Panel, and Bottom Trim as shown. Insert Male Camlocks into the Female Camlocks and tighten using a Phillips Screwdriver. Side Rail Left Side Panel Female Camlock Left Center Panel NOTE: Ensure grooves in Left Side...
- Page 14 Insert (12) Wood Dowels (Part C) into the assembled cabinet as shown. Insert (10) Male Camlocks (Part A) into the underside of the Top Panel (Part 15) as shown. Tighten using a Phillps Screwdriver. Male Camlock Top Panel...
- Page 15 Insert (10) Female Camlocks (Part B) into the cabinet as shown. Female Camlock Place the Male Camlocks in the Top Panel (Part 15) into the Female Camlocks in the Cabinet. Tighten using a Phillips Screwdriver. NOTE: Ensure arrows on Female Camlocks face outward toward the receiver holes. Insert (12) Shelf Support Pins into the holes in the Side and Center Panels.
- Page 16 Insert the Center Shelf (Part 17) and the Left and Right Side Shelves (Part 16) into the assembled cabinet to rest on the Shelf Support Pins (Part D). Right Side Shelf Center Shelf Left Side Shelf Attach (4) Plates (Part K) onto the inside bottoms of the Left Door (Part 18) and Right Door (Part 19) using (8) 4*12mm Screws (Part H).
- Page 17 Attach Handles (Part G) to the Left & Right Doors using included screws. Tighten using a Phillips Screwdriver. Right Door Left Door Handle Insert the Plates into the grooves in the Bottom Trim. Lift up on the door to seat the Pulley onto the Slide Rail.
- Page 18 Attach (14) Plastic Wedges (Part L) into the back panels as shown. Attach using included screws and tighten using a Phillips Screwdriver. Plastic Wedge Wall Strap 1. Attach (2) Wall Straps to the unit using the included Washers and Screws. 2.