Speak to Systemair for more information on how to install the constant airflow temperature of 200 °C in normal working product in different installation locations. conditions. If there is a fire, KBR/F can have a a maximum Product overview Duct connection...
If you do not obey these instructions, there is a risk of damage to the product, other materials or the adjacent area. Use a mobile device to scan the scannable code and go to the Systemair documentation portal for more documentation and document translations.
• Always use spare parts from Systemair. • Sound levels exceeding 70 dB(A) may occur depending on model and size. Visit www.systemair.com for more de- tailed information about your product. • The product is not to be used by persons, including chil-...
– To decrease vibrations transmitted from the product to the duct system, Systemair recommends to install vi- bration dampers, fast clamps or flexible connections. – If you install the product with free suction or free dis- charge, it is necessary to install a protection grille.
Note: • Make sure that the electrical connection agrees with the Systemair recommends to use flexible connections or FK product specification on the motor name plate. fast clamps to attach the duct to the product. Flexible con- • Make sure that the environment for electrical connection nections and FK fast clamps are available as accessories.
• Install the motor cables and the temperature monitor apart. value that is given on the name plate. • If the motor does not have temperature monitors, install a The commissioning report is found at www.systemair.com. motor protection switch. To do before the commissioning •...
EC motors must be set to ON/OFF via the control input. To stop the product via mains supply decreases the life time of the motor. Systemair recommends to install external speed controller for easy access to control the input signal.
Spare parts • For information about spare parts, send an e-mail to support@systemair.com. • For more information about spare parts, contact Systemair support. • Always use spare parts from Systemair. • When you send an order for spare parts, include the serial number of the product.
Troubleshooting Note: If you cannot find a solution to your problem in this section, speak to Systemair technical support. Problem Cause Solution The fan impeller is not correctly Speak to Systemair technical support. balanced. There is dirt on the fan impeller.
Page 12
This is not applicable for EC motors or 3–phase AC motors. There is blockage in the motor. Speak to Systemair technical support. Defective motor winding. If it is possible, measure the resistance to do a check of the motor winding.
Disposal 10.1 To disassemble and discard the parts of the product The product follows the WEEE directive. This symbol on the product or the packaging of the product shows that this Disconnect and disassemble the product in the opposite product is not domestic waste. The product must be recycled sequence of electrical connection and installation.
Technical data overview KBR/F Maximum temperature of transported air, °C Sound pressure, dB Refer to the data sheet in the online catalogue at www.systemair.com. IP class Voltage, current, frequency, enclosure Refer to the name plate. Refer to 1.5 Name plate page 2 for more information.
12.2 Product dimensions Note: If the unit of measure is not specified, the dimensions are given in millimetres. ØJ KBR 280 AC KBR/F 280 AC KBR 280 EC KBR 315 AC 187.5 KBR/F 315 AC 187.5 KBR 315 EC 187.5 KBR 355 AC 206.7...
12.3 Wiring diagrams Refer to the wiring diagram documents that are included in the supply of the product. The wires in the motor cables have these colours: Wire Colour +10V 0...10V/PWM Yellow Blue 12.3.1 Wiring diagrams for speed controllers for EC motors Note: An internal potentiometer is installed on the terminal block from the factory.
12.3.2 Wiring diagrams for ON/OFF controls for EC motors CO2RT-R(-D) Supply +10V 24V AC Neutral 0...10V Common Relay NO Relay NC Din1 IR24–P +10V 24V AC or DC Neutral 0...10V Common Relay NO Relay NC Din1...
ASF: Flexible connection, applicable for KBR fans EVH: Flexible connection, applicable for KBR/F fans WBK: Wall bracket LRK: Airflow shutter ALS: Drain plug UGF: Transition flange WSD: Motor weather protection Note: For more information about accessories, refer to www.systemair.com or speak to Systemair technical support.
Need help?
Do you have a question about the KBR and is the answer not in the manual?
Questions and answers