GE GTDL200GMWW Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Dryer
  5. DuraDrum GTDL200GMWW
  6. Installation instructions manual
GE GTDL200GMWW Installation Instructions Manual

GE GTDL200GMWW Installation Instructions Manual

Ge® 7.0 cu. ft. capacity duradrum™ gas dryer
Hide thumbs Also See for GTDL200GMWW:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
I
I

BEFORE YOU BEGIN

R
IM ORTANT
IM ORTANT
N
I
N
C
TOOLS YOU WILL NEED
(x2)
10" ADJUSTABLE WRENCHES
LEVEL
8" PIPE WRENCH
I
C
WARNING
California Safe Drinking Water and Toxic Enforcement Act
T
W
A
SLIP JOINT PLIERS
FLAT BLADE SCREWDRIVER
G
800 GE CARES US
www.GEAppliances.com (US)
RISK OF FIRE
IN THE COMMONWEALTH OF MASSACHUSETTS
MATERIALS YOU WILL NEED
4" DIA. METAL DUCT
4" DIA. METAL
(RECOMMENDED)
4" DIA. FLEXIBLE METAL (SEMI-RIGID)
UL LISTED TRANSITION DUCT
(IF NEEDED)
CLAMPS (2)
KIT WX08X10077 (INCLUDES 2 ELBOWS)
4" SPRING
CLAMPS (2)
4" DIA. FLEXIBLE METAL (FOIL TYPE)
UL LISTED TRANSITION DUCT
(IF NEEDED.)
08
800
C
T
PIPE
EXHAUST
COMPOUND
ELBOW
HOOD
4" DUCT
DUCT TAPE
OR
FLEXIBLE GAS LINE CONNECTOR
234D1582P008 31-16679 03-12 GE
SOAP SOLUTION
FOR LEAK DETECTION
SAFETY
GLASSES
GLOVES

Advertisement

Table of Contents
loading

Related Manuals for GE GTDL200GMWW

Summary of Contents for GE GTDL200GMWW

  • Page 1: Before You Begin

    (x2) SLIP JOINT PLIERS 10" ADJUSTABLE WRENCHES LEVEL FLAT BLADE SCREWDRIVER 8" PIPE WRENCH 800 GE CARES US www.GEAppliances.com (US) WARNING RISK OF FIRE California Safe Drinking Water and Toxic Enforcement Act IN THE COMMONWEALTH OF MASSACHUSETTS 4" DIA. METAL DUCT (RECOMMENDED) 4"...

  • Page 2: Gas Requirements

    PREPARING FOR INSTALLATION OF NEW RYER TIP I ISCONNECTING GAS TURN GAS DISCONNECT AND DISCARD OLD FLEXIBLE GAS CONNECTOR AND SHUT-OFF OLD DUCTING MATERIAL. VALVE TO THE REPLACE WITH NEW CSA(AGA) OFF POSITION. APPROVED FLEXIBLE GAS LINE CONNECTOR AND UL APPROVED TRANSITION DUCT.
  • Page 3 RECONNECTING GAS Listed connector ANSI Z21.24 / CSA 6.10 FLARE NEW METAL FLEXIBLE GAS LINE CONNECTOR ADAPTER 3/8" NPT ELBOW ITEMS NOT SUPPLIED CAUTION APPLY PIPE COMPOUND TO THE ADAPTER AND DRYER GAS INLET. Tighten the flexible gas line using two adjustable wrenches.

  • Page 4: Exhaust Information

    ELECTRICAL CONNECTION INFORMATION WARNING TO RE UCE THE RISK OF FIRE ELECTRICAL SHOCK AN PERSONAL IN URY O NOT USE AN EXTENSION COR OR AN A APTER PLUG WITH THIS APPLIANCE ELECTRICAL REQUIREMENTS WARNING THIS RYER IS EQUIPPE WITH A THREE PRONG GROUN ING PLUG FOR YOUR PROTECTION AGAINST SHOCK HA AR AN SHOUL BE PLUGGE...

  • Page 5: Exhaust Connection

    SEALING OF OINTS INSULATION EXHAUST CONNECTION BEFORE PERFORMING THIS EXHAUST INSTALLATION BE SURE TO ISCONNECT THE RYER FROM ITS ELECTRICAL SUPPLY WARNING TO RE UCE THE RISK OF FIRE OR PERSONAL IN URY THIS RYER COMES REA Y FOR REAR EXHAUSTING IF SPACE IS LIMITE USE THE INSTRUCTIONS IN STEP EXHAUST IRECTLY FROM THE SI E OR...
  • Page 6 UL LISTE FLEXIBLE METAL SEMI RIGI UL LISTE FLEXIBLE METAL FOIL TYPE TRANSITION UCT ELBOW HIGHLY RECOMMENDED ELBOWS HIGHLY RECOMMENDED DON’T DO NOT USE EXCESSIVE EXHAUST LENGTH TRANSITION UCT LE ELING RYER STAND THE DRYER UPRIGHT NEAR THE FINAL LOCATION AND ADJUST THE 4 LEVELING LEGS TO MATCH THE HEIGHT OF YOUR WASHER.
  • Page 7 MOBILE OR MANUFACTURE HOME INSTALLATION GARAGE INSTALLATION IF ALLOWE BY LOCAL CO ES RYER EXHAUST TO BOTTOM CABINET WARNING BEFORE PERFORMING THIS EXHAUST INSTALLATION BE SURE TO ISCONNECT THE RYER FROM ITS ELECTRICAL SUPPLY PROTECT YOUR HAN S AN ARMS FROM SHARP E GES WHEN WORKING INSI E THE CABINET BE SURE TO WEAR GLO ES REMOVE...
  • Page 8 ING UCT FOR EXHAUST THROUGH BOTTOM OF CABINET CAUTION ING CO ER PLATE TO REAR OF CABINET PL ATE (KIT WE1M454) WARNING NE ER LEA E THE BACK OPENING WITHOUT THE PLATE KIT WE M CHANGING IRECTION OF OOR OPENING REMOVE 4 HOLE PLUGS AND PLACE THEM IN THE HOLES REMOVE 4...

Table of Contents