Related Manuals for Trox Technik X-AIRCONTROL FAM-RD
Summary of Contents for Trox Technik X-AIRCONTROL FAM-RD
- Page 1 Installation and operating manual GB/en X-AIRCONTROL FAM-RD Field Application Module with RadioDuct expansion module...
- Page 2 TROX GmbH Heinrich-Trox-Platz 47504 Neukirchen-Vluyn Germany Phone: +49 (0) 2845 2020 Fax: +49 (0) 2845 202-265 E-mail: trox-de@troxgroup.com Internet: http://www.troxtechnik.com Translation of the original A00000092825, 1, GB/en 09/2022 X-AIRCONTROL FAM-RD...
-
Page 3: Table Of Contents
Diagnosis / troubleshooting....18 Diagnosis information in the configuration software............. 18 Diagnosis information on the main PCB..18 Diagnosis information on the RadioDuct expansion module........19 Technical data.......... 20 Dimensions..........20 Decommissioning........21 Safety............21 Disassembly..........21 Disposal............. 21 X-AIRCONTROL FAM-RD... -
Page 4: Product Overview
Product overview Product overview Fig. 1: FAM-RD FAM-RD (Field Application Module with Radio- Antenna mounting bracket Duct expansion module) Antenna cable, 50 cm long Antenna X-AIRCONTROL FAM-RD... - Page 5 Digital input 1 (DI1 + GND) Not used Digital input 2 (DI2 + GND) Digital input 3 (DI3 + GND) Analogue input 1 (AI1 + GND) Temperature input (TI1 + GND) Power = power supply Digital output DO (NO, C, NC) Not used X-AIRCONTROL FAM-RD...
-
Page 6: General Information
TROX GmbH, these are the reg- ments apply: ulations in section "Vl. Warranty claims" of the FAM-RD product information Delivery Terms of TROX GmbH, see X-AIRCONTROL commissioning and service www.trox.de/en/. manual Project-specific wiring documents X-AIRCONTROL FAM-RD... -
Page 7: Safety
ENVIRONMENT! Environmental pollution hazard. Safety Correct use FAM-RD is used as part of X-AIRCONTROL for radio-based data transmission through ducting. The data is transmitted in two directions between zone module and zone master. X-AIRCONTROL FAM-RD... -
Page 8: Dangers And Risks
Over tightening the fixing screws may damage the device. – Tighten the screws only finger-tight. Qualified staff The work described in this manual has to be carried out by individuals with the qualification, training, knowledge and experience described below: X-AIRCONTROL FAM-RD... -
Page 9: Delivery And Storage
Properly dispose of packaging material. packets it receives from other nodes so that the packets eventually reach their destination. The net- work always tries to find the most efficient route. Such networks are called mesh networks. The con- X-AIRCONTROL FAM-RD... - Page 10 Fig. 4: Radio transmission between zone master and zone module 1 The connection between the first zone module and the zone master is made with one FAM-RD at each end of the transmission route. The zone modules are interconnected by cables. X-AIRCONTROL FAM-RD...
-
Page 11: Installation
ZMA / ZMO must not exceed 30 m. Fix the antenna in the middle of the duct wall (applies to rectangular ducts). Fig. 10: Use the screws to fix the bracket Fig. 7: Position on ducts X-AIRCONTROL FAM-RD... -
Page 12: Electrical Connection
Connect FAM-RD and zone master or zone module with an RJ12 cable: Type AWG26/6C RJ12 plug (6P6C) Max. length 30 m Fig. 13: Connection to zone master – data connec- tion (Modbus) and external power supply X-AIRCONTROL FAM-RD... - Page 13 (Modbus) and power supply with X-AIR- PCASE230 V Fig. 14: Connection to zone master – data connec- tion (Modbus) and power supply with X-AIR- PCASE230 V Zone module Fig. 15: Connection to zone module – data connec- tion (Modbus) and external power supply X-AIRCONTROL FAM-RD...
-
Page 14: Commissioning
Order code: EasyConnect-BC settings. To make a connection to the PC, you need one of the following components: Configuration cable: EasyConnect-CAB Fig. 17: EasyConnect-CAB PC (by others) USB–RS485 and connecting cable (for a wired connection) EasyConnect-CAB X-AIRCONTROL FAM-RD... -
Page 15: Activation
Make the connection according to the have been established, you can con- instructions supplied. figure the zone master, Ä ‘X- AIRCONTROL commissioning and service manual’ . Press the [Push Service] (Fig. 19/1) button on the FAM-RD for 2 seconds to activate port Service/T1. X-AIRCONTROL FAM-RD... - Page 16 Set the ‘Operation mode’ to ‘Zone module’ . To use the Pan ID and network key saved earlier as part of the RadioDuct master con- figuration, click on [Load network settings]. Click on [Transmit changes] to transmit your entries to the zone module. X-AIRCONTROL FAM-RD...
- Page 17 Make the connection according to the instructions supplied. Press the [Push Service] (Fig. 19/1) button on the module for 2 seconds to activate port Service/T1. Fig. 23: Repeater configuration for RadioDuct Go to the ‘Configuration’ page. Set the ‘Operation mode’ to ‘Repeater’ . X-AIRCONTROL FAM-RD...
-
Page 18: Diagnosis / Troubleshooting
Diagnosis information on the main PCB Fig. 24: X-AIRCONTROL with one mesh connection Fig. 25: X-AIRCONTROL with two mesh connec- tions Fig. 27: Diagnosis information on the main PCB Fig. 26: X-AIRCONTROL with one mesh connection that includes a repeater X-AIRCONTROL FAM-RD... -
Page 19: Diagnosis Information On The Radioduct Expansion Module
- Connection to at least one node (device) has been established and is working - Module has not been configured with the network parameters Blinking, - Master has been configured, but no 1 Hz network device has initiated a con- nection X-AIRCONTROL FAM-RD... -
Page 20: Technical Data
10 to 50 °C Blinking - Data transmission in progress, blinking Protection level IP20 frequency depends on data transmis- sion rate CE conformity EMC directive 2014/30/EU RoHS 2011/65/EU Radio equipment directive ‘RED 2014/53/EU’ Weight 500 g X-AIRCONTROL FAM-RD... -
Page 21: Decommissioning
Physically disconnect the unit from the power supply and make sure that any stored residual energy is discharged. Remove any other connected cables. Then disassemble the device professionally in com- pliance with local occupational safety and environ- mental protection regulations. X-AIRCONTROL FAM-RD... - Page 22 RadioDuct Config Tool Software............18 Software............14 Dimensions............20 Radio frequency..........20 Disassembly............21 Radio status............18 Disposal.............. 21 Repeater Setup............17 Electrical connection........... 12 Residual risks............8 Functional description........... 9 Service..............6 Signal quality............18 Hotline..............6 X-AIRCONTROL FAM-RD...
- Page 23 Weight..............20 Diagnosis............18 Wiring examples..........12 Storage ..............9 Supply package............ 9 X-AIRCONTROL Symbols..............7 Commissioning..........18 Technical data............. 20 Zone master............9 Technical Service..........6 Setup............15 Timeout............... 18 Zone module............9 Transport............... 9 Setup............16 X-AIRCONTROL FAM-RD...
- Page 24 X-AIRCONTROL FAM-RD...
Need help?
Do you have a question about the X-AIRCONTROL FAM-RD and is the answer not in the manual?
Questions and answers