Subscribe to Our Youtube Channel
Related Manuals for Trox Technik QL-WF-EO
Summary of Contents for Trox Technik QL-WF-EO
- Page 1 L-08-1-55e Installation manual Displacement flow diffusers QL-WF-EO QL-WF-EU With plinth Without plinth...
-
Page 2: Table Of Contents
1. General information This installation manual describes the following type of displace- ment flow diffuser: 2. Safety and correct use General safety notes QL-WF-EO Standards and guidelines QL-WF-EU Repair and replacement parts Environmental protection / disposal To ensure correct functioning of the displacement flow diffuser,... -
Page 3: Safety And Correct Use
Installation manual Displacement flow diffuser QL-WF-E 2. Safety and correct use General safety notes VORSICHT! WARNUNG! Verletzungsgefahr an scharfen Kanten, Graten, spitzen Verletzungsgefahr bei unzureichender Qualifikation! Ecken und dünnwandigen Blechteilen! Unsachgemässer Umgang kann zu erheblichen Personen- – Bei allen Arbeiten vorsichtig vorgehen. und Sachschäden führen. -
Page 4: Standards And Guidelines
Installation manual Displacement flow diffuser QL-WF-E Standards and guidelines order to reduce health or safety hazards to the minimum. For all work on the displacement flow diffuser, the following provi- sions and guidelines among others must be observed The appropriate protective equipment for a job must be worn for - Product Safety Laws (PrSG) as long as the job takes. -
Page 5: Transport, Storage And Packaging
The QL-WF-EO/EU is suitable for installation on a your supplier immediately. Put the product back into its packa- wall, one way discharge, and is available with or without plinth. -
Page 6: Dimensions
Installation manual Displacement flow diffuser QL-WF-E Dimensions B… x H… x T… QL-WF-EO B + 2 mm B + 2 mm B + 2 mm B + 2 mm 5. Technical data Technical data in Brochure L-08-1-04d. -
Page 7: Installation
Installation manual Displacement flow diffuser QL-WF-E 6. Installation 1 QL-WF-EO Duct connection top or QL-WF-EU Duct connection bottom Tool for loosening the perforated face plate from the nozzle plate 2 On-site positioning of the displacement flow diffuser QL-WF-EO QL-WF-EU... - Page 8 Installation manual Displacement flow diffuser QL-WF-E 3 Removing the perforated face plate with the supplied tool. QL-WF-EO QL-WF-EU 4 Loosening the fixing screw of the nozzle plate. QL-WF-EO QL-WF-EU...
- Page 9 Installation manual Displacement flow diffuser QL-WF-E 5 Carefully lifting the nozzle plate out. QL-WF-EU QL-WF-EO...
- Page 10 Installation manual Displacement flow diffuser QL-WF-E 6 Fixing the plenum box The mounting screws are not included in the supply package, screw hole Ø 6 mm. QL-WF-EO QL-WF-EU...
- Page 11 Installation manual Displacement flow diffuser QL-WF-E 7 Carefully reattaching the nozzle plate. QL-WF-EO QL-WF-EU 8 Fixing the nozzle plate with the fixing screws. QL-WF-EO QL-WF-EU...
- Page 12 Installation manual Displacement flow diffuser QL-WF-E 9 Installing the perforated face plate. QL-WF-EO QL-WF-EU Duct connection The plenum box has a spigot for duct connection. Variants with a double lip seal allow for a sufficiently tight connection; additional Den Frontdurchlass möglichst erst nach Abschluss aller sealing is not required.
-
Page 13: Initial Commissioning
Installation manual Displacement flow diffuser QL-WF-E Initial commissioning Before you start commissioning: - Check that the air terminal devices are seated correctly. - Remove protective film. - Ensure that all air terminal devices are clean and free from residues and foreign matter. - Check that electrical connections have been correctly assembled.
Need help?
Do you have a question about the QL-WF-EO and is the answer not in the manual?
Questions and answers