Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chiltern Invadex OHWLTRK-1
Summary of Contents for Chiltern Invadex OHWLTRK-1
- Page 1 Portable Gantry user guide Wispa LiteTrack...
-
Page 2: Table Of Contents
User Guide Contents Intended use of the Product ......2 Things to consider before using the Gantry ..............2 Assembly Guide ..........4 Disassembly guide .......... 11 Servicing & maintenance ........ 15 Parts ..............15 Troubleshooting ..........16 Gantry Specification ........17 Warranty ............ -
Page 3: Intended Use Of The Product
It should be used with the WispaLite Portable Hoist and a Wispa sling or other lifting accessories from the Chiltern Invadex range, as assessed by a trained person. Note: Not all slings and accessories are compatible with the Wispa Lite hoist. - Page 4 Chiltern Invadex. • Do not touch any of the moving parts in the hoist unit or in the track. Call Chiltern Invadex for assistance. • Always ensure the legs are positioned as shown in Fig 13 of this user guide •...
-
Page 5: Assembly Guide
Chiltern Invadex LiteTrack Portable Gantry LiteTrack Gantry Assembly Instructions Check all components are available prior to assembly. Notes: If the gantry is to be assembled over a bed The gantry can be assembled over a bed unless it is occupied. If the... - Page 6 User Guide 3. Locating the leg Fig 3 and foot sections and inserting the gas strut Where there is limited head room it is recommended that the foot section is laid on its side for assembly as Fig 3. Insert the gas strut in the orientation shown in Fig 3.
- Page 7 Chiltern Invadex LiteTrack Portable Gantry 5. Assembling the Fig 5 cassette and end beams Notes: 1. The end beams which attach to the cassette are identical. 2. The cassette can be positioned either way round. 3. Assemble the cross beam as close to the legs as possible.
- Page 8 User Guide 7. Fold over the Fig 7 corner quadrant on both end beams in preparation for connecting to the leg as Fig 7 (A). Ensure the cassette is centralised in the correct position (latched). To achieve this slide along until it clicks into position in the centre of the rail as Fig 7 (B).
- Page 9 Chiltern Invadex LiteTrack Portable Gantry 9. Securing the Fig 9 cross beam to the cassette Adjust the position of the leg as Fig 8.2 (B) to allow the corner quadrant to be connected (this should be at 90 degrees to the leg and cross beam).
- Page 10 User Guide 12. Adjusting the Fig 12 height of the gantry Position the gantry in its required location prior to adjusting the height and checking level. Take care when moving the gantry to the desired location. Move one leg at a time in small increments.
- Page 11 Chiltern Invadex LiteTrack Portable Gantry Final positioning Fig 14 14. Attaching the Wispa Lite Portable hoist Rest the Portable hoist on the bed or trolley ready for attaching to the eye on the gantry. Release sufficient tape to connect the...
-
Page 12: Disassembly Guide
User Guide 16. Disassembly of the gantry Do not lift the hoist. Lower the hoist by releasing sufficient tape to disconnect the carabena on the hoist from the eye on the gantry as Fig 16 (B). Remove the hoist from the gantry. Always ensure the cassette is locked in the central position before disassembling the gantry. - Page 13 Chiltern Invadex LiteTrack Portable Gantry 17. Important safety Fig 17 note: 1. Completely remove one leg BEFORE releasing the second leg. 2. Ensure there is sufficient space to lower the gantry. Remove the upper handwheel which locks the corner quadrant in place as...
- Page 14 User Guide 19. Fold back the Fig 19 corner quadrant as Fig 19 (A), depress the release lever as Fig 19 (B) and slide out the end beam section as Fig 19 (C). Repeat for other side. 20. Leg Fig 20 disassembly Where there is limited head room it is...
- Page 15 Chiltern Invadex LiteTrack Portable Gantry Width calculation guide The table below can be used as a quick reference guide to help determine the internal width of the gantry (depending on the hole position which has been selected). For example - when the first hole position is...
-
Page 16: Servicing & Maintenance
Further details can be obtained from any Chiltern Invadex Office, shown on the back of this booklet. Chiltern Invadex and its Authorised Dealers are able to carry out all aspects of servicing and maintenance work. Maintenance of this equipment should only be conducted by engineers trained and certified by Chiltern Invadex. -
Page 17: Troubleshooting
Chiltern Invadex LiteTrack Portable Gantry Troubleshooting symptom suggested cause solution Cassette travels Cable tension is Contact Chiltern further in one direction incorrect Invadex for assistance along the beam than the other Pins do not click into Leg section is Adjust leg position... -
Page 18: Gantry Specification
Cassette (x1) 11kg (24lb) End section/corner quadrant (x2) 5kg each (11lb) Gas strut (x2) 1kg each (2.2lb) Total weight of gantry 53kg (116lb) CE MARK The Chiltern Invadex Wispa LiteTrack Gantry carries the CE mark and complies with EC Directives: Medical Device Directive(93/42/EEC) -
Page 19: Warranty
Chiltern Invadex for the safety of this product. 6. Chiltern Invadex shall in no event be liable for any damages, costs or expenses arising from any claim made under this warranty (save for any legal liability of Chiltern Invadex for death or personal injury resulting from the company’s... -
Page 20: Gantry Service Record
User Guide Gantry Service Record Serviced By (company) ..................Telephone no..................Engineers training cert. no. Signature ....................Date: ......Load Tested To: ......Kgs Comments........................................Serviced By (company) ..................Telephone no..................Engineers training cert. no. Signature ....................... Date: ......Load Tested To: ......Kgs Comments .................. - Page 21 Chiltern Invadex LiteTrack Portable Gantry Gantry Service Record Serviced By (company) ..................Telephone no..................Engineers training cert. no. Signature ....................Date: ......Load Tested To: ......Kgs Comments........................................Serviced By (company) ..................Telephone no..................Engineers training cert. no. Signature ..............
- Page 22 Models covered Please fill in the information below for future reference OHWLTRK-1 OHWLTRK-2 Dealers Name ................Address ................................... Post Code......... Telephone ............Your Serial Number is ........Date of purchase ......
- Page 23 FM 21085 Copyright © Chiltern Invadex Ltd. The design of the product shown in this User Guide is vested in Chiltern Invadex Ltd and should not be copied or reproduced in anyway whatsoever without the express permission in writing of Chiltern Invadex Ltd.
Need help?
Do you have a question about the OHWLTRK-1 and is the answer not in the manual?
Questions and answers