Advertisement
Quick Links
S
E
N
D
U
M
W
I
R
E
L
E
S
S
G T 3 0 0 E q u i p m e n t M a n a g e m e n t S y s t e m
SENDUM GT300
GT300 QUICK INSTALLATION GUIDE
SENDUM WIRELESS
Customer Service and Support
4 5 0 0 B e e d i e S t r e e t , B u r a n b y, B C V 5 J 5 L 2 C a n a d a
t e l e p h o n e : + 1 6 0 4 . 4 3 9 . 6 7 4 6
f a x : + 1 6 0 4 . 4 3 7 . 5 7 2 6
•
•
•
w w w. s e n d u m . c o m
Advertisement
Related Manuals for Sendum GT300
Summary of Contents for Sendum GT300
- Page 1 G T 3 0 0 E q u i p m e n t M a n a g e m e n t S y s t e m SENDUM GT300 GT300 QUICK INSTALLATION GUIDE SENDUM WIRELESS Customer Service and Support 4 5 0 0 B e e d i e S t r e e t , B u r a n b y, B C V 5 J 5 L 2 C a n a d a t e l e p h o n e : + 1 6 0 4 .
- Page 2 “Title 30 of the Code of terminal. devices can create an In order to prevent injury or death, all machines equipped with the Sendum GT300 system are required to have the Federal Regulations (CFR)” to ensure safe operation in the storage, transportation, loading, and explosion.
- Page 3 GlobalTRACS Lite system, especially on battery-powered equipment. Both the Sendum GT300 system power/signal cable should be run to the negative side of the battery (BAT -) on battery powered equipment. Always verify a good ground by measuring with an ohm meter from the battery return (BAT_RTN) wire and the chassis ground (C_GND) wire on the GlobalTRACS negative battery terminal to where the ground wire will be attached.
- Page 4 Sendum GT300 System Quick Installation Procedures Survey the Equipment The Sendum GT300 system may not be suitable for use on certain types of heavy equipment with high vibration specifications. Sendum recommends consulting the equipment manufacturer’s specification manual to determine if the Sendum GT300 system can operate on the equipment.
- Page 5 Do not mount the GT300 near items that may fall on it or bump cable connections. battery may create a shock 15-J5772-1 hazard and can cause product damage, serious • Choose a structurally rigid mounting location. The surface must support the full weight of the GT300 under injury or death. all circumstances. 15-J5773-1 04AAA_145c_QIG •...
- Page 6 Mount the GT300 with one of the mounting bolts. when power is off, resulting in maintenance or welding on serious injury or death.
- Page 7 Continuity must be at 0 ohms. Always verify 0 ohms at both connections to ensure proper grounding is established. Route the power/signal cable from the GT300 to the designated vehicle power source. Attach one 3-amp fuse to the power wire.: Refer to all published equipment manufacturer cautions and warnings.
- Page 8 Power/Signal Cable Wire Connections For Diesel Powered Equipment The equipment battery supplies the power to the GT300 There are four required wire connections that you must make from the power/signal cable: • BATTERY (black) to +12 VDC or +24 VDC battery •...
- Page 9 Failure to disconnect the The equipment battery supplies the power to the GT300. There are four required wire connections that you must battery may create a shock 15-J5772-1 make from the power/signal cable: hazard and can cause product damage, serious injury or death.
- Page 10 All trademarks are the property of their respective owners. Specifications are subject to change without notice. Sen- dum endeavors to ensure that the information in this document is correct and fairly stated, but Sendum is not liable for any errors or omissions. Published information may not be up to date, and it is important to confirm current status with Sendum.
Need help?
Do you have a question about the GT300 and is the answer not in the manual?
Questions and answers