Advertisement
Please read this manual before use and follow its guidance. Keep this manual for future reference.
Note:
Before opening the parcel, please check whether if the parcel is damaged or not. If the product is damaged during delivery or if any items went missing upon arrival, please contact Seller customer service (service@kayomaxtar.com) to get it solved. You should receive the following items:
Item | Number of item | |
1 | Portable solar power generator![]() | 1 |
2 | AC wall charger (Including AC input charging cable)![]() Picture is only for reference, pls take the product as the standard | 1 |
3 | PV solar charge cable(7909 to MC4)![]() | 1 |
4 | User manual![]() | 1 |
5 | Warranty card![]() | 1 |
6 | Certificate of qualification![]() | 1 |
Attention:
Note: check to make sure the product is turned on. Otherwise, you can not turn on AC/ DC output.
Turn off generator, connect PV( or charger)to charge, activate PV charge function, the first column on screen will be lit up and show input power, at this time, the generator is in charging state, can not support AC and DC functions. If want to open AC and DC functions, need to press master power button more than 1 second to turn on the generator, screen will be all lit up after generator be turned on. After start-up, connect PV(or charger) to start charging, screen shows input power wattage, at this time, can open AC and DC functions.
Notice:
To charge the product, insert the solar charging cable or AC adapter into the input port of the product. The display screen would light up and the charging power would be displayed. But don't care this the wrong way. The product will not turn on by itself when being charged. If the product is previously turned off, it will remain turned off unless you manually turn it on.
Insert one end of the adapter into wall outlet and insert the other end to the input port of the product. Then, the product will be charged and you can monitor the battery status by checking the battery icon on the LCD screen The product comes with a built-in advanced control circuit. When the battery is fully charged, it will stop charging itself automatically.
Cold weather can influence battery capacity. In sub-zero temperature (<0°C), you may be able to discharge the product, but you should not charge it. Otherwise, the battery of the product would be greatly damaged and the capacity may not even be recovered. Low temperature charging protection: When the product is charged at a temperature below 0°C, it will shut off and stop charging itself automatically. The product will reboot and start charging itself when the temperature rise to above 10°C. Low temperature discharging protection: If the product is discharged at a temperature of -20°C, it will turn off. The product will reboot and turn on output when the temperature rise to above -10°C.
The battery icon indicates the battery level of this product. The battery level is displayed in 5 segments. When battery is being charged, the icon would flash. When the battery is fully charged, the icon would stop flashing and all 5 segments will be filled.
You need to check the power at each output port. For example, the power at AC output port is provided by the built-in inverter of the product, whose maximum continuous output power is 1000W. This means that it is only suitable for electronic device whose required power is no more than 1000W.
Cooling fan will start working automatically when the following conditions are met:
Besides, generator intelligent system will adjust the PV input or AC output power based on the outer case temperature, to keep the outer case at a touchable temperature.
Note: Do not use the machine when the cooling tan is broken.
When the product is powered on, turn on DC output and keep the AC output turned off. Press and hold both DC button & AC button to enter setting mode Press AC power button to choose inverter AC output frequency. Press and hold both DC and AC power button to exit frequency setting mode Restart the machine.
Error | Problem | Solution |
E001 | Over-voltage protection (battery pack) | Stop charging and start discharging. |
E002 | Under-voltage protection (battery pack) | Please charge the product in time. Restart the machine once it is fully charged. |
E003 | Battery failure | Restart the machine and charge it. |
E004 | Over-temperature protection when dis- charging the battery. | Wait for a while for it to cool down and then restart the machine. |
E005 | Under-temperature protection when dis- charging the battery. | Wait for a while for it to heat up and then restart the machine. |
E006 | Over-temperature protection when charging the battery. | Wait for a while for it to cool down and then restart the machine. |
E007 | Under-temperature protection when charging the battery. | Wait for a while for it to heat up and then restart the machine. |
E008 | Under-voltage protection for the 1st cell. | Please charge the product in time and re-start it when fully charged. |
E009 | Under-voltage protection for the 2nd cell. | Please charge the product in time and re-start it when fully charged. |
E010 | Under-voltage protection for the 3rd cell. | Please charge the product in time and re-start it when fully charged. |
E011 | Under-voltage protection for the 4th cell. | Please charge the product in time and re-start it when fully charged. |
E012 | Busbar fault of inverter due to under-volt- age. | Turn off and on the machine. |
E013 | Over-load protection of inverter. | Check if the output port of inverter is over-loaded. Turn off and on the AC output to recover. |
E014 | Output port of inverter is short-circuited. | Check if the output port of inverter is short-circuited. Turn off and on the AC out-put to recover. |
E015 | The heat sink of inverter is overheated. | Wait for it to cool down and then restart the machine. |
E016 | The temperature of the heat sink is not detected. | Insert the NTC and restart the machine. |
E017 | Over-voltage protection (PV input). | Disconnect the solar charging cable and then restart the machine. |
E018 | Over-voltage protection (PV output) | Disconnect the solar charging cable, re-start the machine and then re-insert the solar charging cable. |
E019 | Over-temperature protection of heat sink for PV module | The heat sink for PV module overheats. Wait for it to cool down and then charge it. |
E020 | The temperature of the heat sink for PV module is not detected. | Restart the machine. |
E021 | Charging protection of battery protection board | Wait for the temperature to return to an acceptable temperature and then start charging. |
E022 | Battery protection | Disconnect the solar charging cable and restart the machine. |
E023 | Over-power protection (system) | Check if the total output power is overloaded. Restart the machine. |
If you have tried the methods mentioned above, but the problem still cannot be solved. Contact seller customer service team. |
ATTENTION!
If you cannot find the solution for your problem in the chart above, please provide the following information to our customer service team:
Model | EB120 | EB150 | EB180 | EB240 | |
Output Specifications | |||||
Inverter Output | Continuous Output Voltage | 100-120Vac, 220-240Vac | |||
Rated Frequency | 50/60Hz | ||||
Continuous Output Power | 1000W | ||||
Power Factor | 1 | ||||
THDV@0.7R (under nominal voltage) | <5% | ||||
Over-load protection | 1000W ≤Load<1200W @2Min; 1200W≤Load @1s; | ||||
Power Loss (No Load & Turned-off) | <20W | ||||
Max Efficiency (>70% Load) | 88%(100-120Vac), 90%(220-240Vac) | ||||
12V/9A Cigar Lighter Output | Continuous Output Voltage | 12.2V(±1V) | |||
Continuous Output Current | 9A | ||||
5V USB Output | Output Voltage Range | 5V±0.3V | |||
Max Output Current | 3A | ||||
Note: The maximum output of a single USB port is 3A. The maximum output of 2 USB ports is 3A((top and down). | |||||
Type-C PD Output | Supported Fast Charge | PD Protocol | |||
Output Voltage Range | 5-20V(±5%) (5V by default) | ||||
Continuous Output Voltage/Current | (5V/9V/12V/15V)3A(±0.3A), 20V/2.25A(±0.2A) | ||||
Input Specification | |||||
AC Adapter Charger | 42V/200W | ||||
PV Max Input Power | 500W | ||||
PV Input Voltage Range | 16-60Vdc(OVP 73V±2V) | ||||
PV Max Input Current | 10A | ||||
MPTT Efficiency | 99.5% | ||||
Max Efficiency | >88% | ||||
Solar Charging Mode | MPPT |
Battery | ||||
rated voltage | 14.8Vdc | |||
rated capacity | 1200Wh | 1500Wh | 1800Wh | 2400Wh |
built-in battery cell | Li-ion | Li-ion | Li-ion | Li-ion |
battery packing | 4S30P | 4S3P | 4S45P | 4S60P |
Min Unit | ||||
IP Rating | IP 21 | |||
Operating Environment | Relative Humidity: 10%-90% | |||
Operating Temperature: 0-40°C | ||||
Dimensions | 293.5*165.4*364.7mm | 371.5*165.4*364.7mm | 393.5*165.4*364.7mm | 493.5*165.4*364.7mm |
Net Weight | 12.6 KG | 17.2 KG | 17 KG | 22 KG |
Note: When the total output power exceeds 1000W, the DC output will be directly shut down. When the load is less than 30W, the output power would not be displayed. When a high-power appliance is attached to the product, the displayed output power and the actual output power could be different for up to 30W. |
Our company provides customers with warranty of 12 months from the date of purchase.
For any inquiries or comments concerning our products, please contact seller (service@ kayomaxtar.com) and we will respond as soon as possible
FB public page: MaxoakDirect
Twitter: Maxoak_fans
Instagram: Maxoak.fans
P/N:16.061.00223-01A0
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download BLUETTI EB120, EB150, EB180, EB240 Portable Power Station Manual
Advertisement
Need help?
Do you have a question about the Bluetti EB120 and is the answer not in the manual?
Questions and answers