Table of Contents
Advertisement
Quick Links
TRUST 814 PCI SURVEILLANCE INTERFACE
Instructions when using for the first time
Installing Direct X 8.1
1.
Uninstalling old drivers and devices
2.
Installation in Windows
3.
Testing
4.
1
Introduction
This instruction manual is for users of the TRUST 814 PCI SURVEILLANCE
INTERFACE. This interface card offers the following possibilities:
•
Interface card for connecting 4 video cameras at the same time for the fully
programmable registration of video monitoring.
•
24 hours/day remote viewing via the Internet or a network connection.
•
Adjustable observation area and sensitivity for an accurate level of detection.
•
Automatic video recording registration with the exact date and time when
motion is detected.
•
Pre-programmed or customized sound signals if motion is detected.
•
Makes a complete (wireless) monitoring system with the security cameras
from the Trust range. Ideal for all forms of safety and observation, for
example, for protection against burglary, supervision of children, shop
entrances, tills, warehouses, car parks, etc.
2
Safety
Carefully read the following instructions before use:
- Do not submerge the device in liquid. This will damage the device. Do not use this
device near water.
3
Installation
Note:
The latest driver can be downloaded from www.trust.com/12948. Check
whether a new driver is available and use this for the installation. The
driver version is printed on the CD-ROM.
Note:
Make sure all other programs are closed during the installation.
Note:
During installation in Windows XP, you may receive a message saying
that the driver has not been signed. This does not cause a problem for
the functionality.
Note:
In the example, 'D:\' is used to indicate the CD-ROM drive. This may be
different for your computer.
!
Chapter
(3.1)
(3.2)
U K
(3.3)
(3.4)
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Trust 814
Summary of Contents for Trust 814
- Page 1 (3.3) Testing (3.4) Introduction This instruction manual is for users of the TRUST 814 PCI SURVEILLANCE INTERFACE. This interface card offers the following possibilities: • Interface card for connecting 4 video cameras at the same time for the fully programmable registration of video monitoring.
-
Page 2: Uninstalling Old Drivers And Devices
It is not possible to install the interface card if you do not install Direct X 8.1 (4.08.01.0810) or a newer version. Insert the CD-ROM into your CD-ROM drive. The Trust Software Installer will start automatically. If it does not start automatically, carry out the following: Select 'Run' from the Start menu. -
Page 3: Checking After The Installation
Follow the on-screen instructions. Installing Trust Remote Camera Install Trust Remote Camera on a different computer to the one on which you have installed the interface card. Trust Remote Camera must be installed if you wish to log onto the computer on which the interface card is installed from a different location via a network or an Internet connection. -
Page 4: Connecting The Camera
Initially required procedure Make sure the computer is turned on and Windows is running. Click on ‘Start – Programs – Trust – 814 PCI Surveillance Interface – X Guard – XGuard’. Figure 2 will appear. Four windows will appear, namely camera #1, camera #2, camera #3 and camera #4. - Page 5 TRUST 814 PCI SURVEILLANCE INTERFACE The indicator in the bottom left-hand corner of the camera window will be lit red. Slowly move the slide bar towards 0% and stop when the indicator in the bottom left-hand corner becomes green. The sensitivity has now been optimally set.
-
Page 6: Setting The Interval Time
Remote Camera software is installed is called the ‘Remote PC’. The computer on which the Trust X Guard and 814 PCI Surveillance Interface card have been installed must be online. This computer is called the ‘Server PC'. It is best to use an ADSL or cable Internet connection because of the fixed connection and the speed on the Internet. - Page 7 Configuring the Trust Remote Software Start the computer on which the Trust Remote Camera has been installed. This is the ‘Remote PC'. Click on ‘Start – Programs – Trust – 814 PCI SURVEILANCE INTERFACE – Remote Camera – RemoteCam’. Figure 10 will appear.
- Page 8 This indicates that you wish the connection between the ‘Server PC’ and the ‘Remote PC’ to be made via the ‘IPX/SPX’ protocol. The ‘Server PC’, which has the Trust X Guard software installed on it, has been set to accept a connection via the IPX/SPX protocol.
- Page 9 In this component, indicate in the ‘Adapter’ field via which modem you wish to make a connection. The ‘Server PC’, which has the Trust X Guard software installed on it, has been set to accept a connection via a modem-to-modem connection.
- Page 10 The Video File Data Base enables you to view the entire history of the recorded events. Both Trust X Guard and Trust Remote Camera have an independent Video File Data Base. The video file is located in the Trust X Guard and Trust Remote camera software file in the Windows Start menu.
-
Page 11: Troubleshooting
TRUST 814 PCI SURVEILLANCE INTERFACE Troubleshooting Method Read the solutions given below. Check for up-to-date FAQ’s, drivers and instruction manuals on the Internet (www.trust.com/12948) Problem Cause Possible solution The Interface card Drivers cannot be Specify the location as the found. - Page 12 Remote Camera software. If you still have problems after trying these solutions, please contact one of the Trust Customer Care Centers. You can find more information at the back of this instruction manual. Please have the following information available: •...
Need help?
Do you have a question about the 814 and is the answer not in the manual?
Questions and answers