Related Manuals for Westwood Design WOODLAND ADVENTURES DP-CR-3101NR-ELM
Summary of Contents for Westwood Design WOODLAND ADVENTURES DP-CR-3101NR-ELM
- Page 1 WOODLAND ADVENTURES Convertible Crib w/Drawer Model: DP-CR-3101NR-ELM CR-3101NR Assembly Instruction...
- Page 2 1-908-719-4707, or emailing support@westwoodbaby.com If any aspect of these instructions is unclear, please contact your retailer or Westwood Design for assistance. In addition to meeting our own extensive in-house testing and standards, this crib has been independently tested to meet JPMA certification standards.
- Page 3 SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE. DO NOT USE CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR DEALER OR CONTACT WESTWOOD DESIGN: 635 N. BILLY MITCHELL RD., STE. B, SALT LAKE CITY, UTAH 84116, PHONE: 1-908-719-4707, EMAIL: SUPPORT@WESTWOODBABY.COM; FOR REPLACEMENT...
- Page 4 Parts & Hardware Included Headboard (x1) Footboard Top (x1) Footboard Base (x1) Crib End, Left (x1) Crib End, Right ( x1 ) Day Bed Cap, Left ( x1 ) Day Bed Cap, Right (x1) Mattress Support (x1)
- Page 5 Parts & Hardware Included Storage Back Panel (x1) Storage Side Panel, Left (x1) Storage Side Panel, Right (x1) Storage Center Panel (x1) Storage Support Legs ( x2 ) Drawer Face, Left ( x1 ) Drawer Face, Right ( x1 ) Drawer Side Panel, Left ( x2 )
- Page 6 Parts & Hardware Included Drawer Side Panel, Right ( x2 ) Drawer Back Panel ( x2 ) Drawer Bottom Panel ( x2 ) JCBC Bolt M6 x 30mm (x14) Wood Screw M8 x 32mm ( x16 ) Wood Dowel 10 x 30mm ( x6 ) Wood Dowel 8 x 30mm ( x8 ) Handle Screw 20mm ( x4 ) Handle ( x2 )
- Page 7 Required Parts & Hardware (A) Headboard ( x1 ) (D) Crib End, Left ( x1 ) (E) Crib End,Right ( x1 ) (Z) Allen Wrench Step 1...
- Page 8 Required Parts & Hardware (I) Storage Back Panel (x1) (J) Storage Side Panel, Left ( x1 ) (K) Storage Side Panel, Right ( X1 ) (L) Storage Center Panel ( x1 ) (T) JCBC Bolt M6 x 30mm (V) JCBC Bolt M6 x 30mm (Z) Allen Wrench ( x8 ) ( x6 )
- Page 9 Required Parts & Hardware (C) Footboard Base (x1) (T) JCBC Bolt M6 x 30mm (Z) Allen Wrench ( x6 ) Step 3...
- Page 10 Required Parts & Hardware (Z) Allen Wrench Step 4...
- Page 11 Required Parts & Hardware Mattress Support (x1) (Z) Allen Wrench Step 5 There are three possible height settings. The mattress support should be at the highest setting for a newborn, then adjust to the lower position as the child grows and becomes mobile. Once the child is able to stand, adjust to lowest position.
- Page 12 Required Parts & Hardware Footboard Top (x1) (Z) Allen Wrench Step 6...
- Page 13 Required Parts & Hardware (N) Drawer Face, Left (x1) Tool required - Screwdriver (O) Drawer Face, Right (x1) (not provided) (P) Drawer Side Panel, Left ( x2 ) (Q) Drawer Side Panel, Right ( x2 ) (U)Wood Screw M8 x 32mm (W)Wood Dowel 8 x 30mm (R) Drawer Back Panel ( x2 ) ( x8 )
- Page 14 Required Parts & Hardware (X)Handle Screw 20mm (Y) Handle ( x2 ) ( x4 ) Step 9 Screwdriver - Not provided Step 10 Drawer, Right Drawer, Left...
- Page 15 DAY BED CONVERSION Day Bed Cap, Left (x1) Day Bed Cap, Right (x1) (Z) Allen Wrench Step 1 The day bed can only be used with the mattress support in its lowest position. Remove the bolts from the footboard using the allen wrench provided.
-
Page 16: Care And Maintenance
CARE AND MAINTENANCE - After completing assembly, check that all bolts and screws are secure and tight. Hardware can become loose over time, so it is your responsibility to periodically check the tightness of all fasteners for as long as you use the crib. - Wood is a natural material.