Marantz AV7703 Service Manual page 141

1.6. Confirmation items for the video system
See the block diagram fig.XXth.
Paths to be confirmed Display (Sub Display)
fig.14
1 Analog Video pass
V01:VIDEO PASS
Video Convert
fig.15a
2 (Analog or HDMI ⇒
V02:V.CONVERT
fig.15b
HDMI)
HDMI pass
fig.16
3
V03:HDMI PASS
(MAIN ZONE)
HDMI CEC
4 (Control Monitor : fig.17
V04:HDMI CEC
HDMI Monitor1)
fig.18a
HDMI Audio
5 fig.18b
V05:H.AUDIO-AVR
(Audio : AVR)
fig.18c
HDMI Audio fig.19a
6
V06:H.AUDIO-TV
(Audio : TV) fig.19b
7 GUI fig.20
V07:GUI MENU ON
HDMI pass
8 fig.21
V08:ZONE2 HDMI
(MAIN ZONE2)
Settings
Input Source : CBL/SAT
Video Conversion (IP Scaler) : Off
MAIN ZONE : On
ZONE2 : On
ZONE3 : Off
Input Source : CBL/SAT
Video Conversion (IP Scaler) : On, All sources
IP Scaler : "Analog&HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
Input Source : CBL/SAT
Video Conversion (IP Scaler) : Off
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
Input Source : CBL/SAT
HDMI Control : On
Control Monitor : Monitor1 (if checking the HDMI Monitor Out1)
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
Input Source : CBL/SAT
HDMI Control : Off
HDMI Audio : AVR (if checking the audio output from AVR)
HDMI Audio : TV (if checking the audio output from TV)
Input Source : CBL/SAT
Video Conversion (IP Scaler) : On, All sources
IP Scaler : "Analog&HDMI", All sources
Resolution : "AUTO", All sources
Setup Menu : On
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
Input Source : CBL/SAT
Z2 Source : Source
MAIN ZONE : On
ZONE2 : On
ZONE3 : Off
141
What to confirm
・ Component input ⇒ Component output
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input ⇒ IP Scaler ⇒ HDMI output.
・ ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
・ CVBS input ⇒ IP Scaler ⇒ HDMI output.
・ Component input ⇒ IP Scaler ⇒ HDMI output.
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (MAIN function) ⇒ HDMI output (MAIN)
( b The input source can be switched to any source except CBL/SAT.)
・ When the power supply of a TV is put in the standby mode, make sure that the power supply
of this unit is also put in the standby mode.
( b The input source can be switched to any source except CBL/SAT.)
・ The ARC path can also be checked (check this using the TV input source).
・ HDMI input (PCM, DolbyDigital, DTS) ⇒ Speaker output.
・ HDMI input(HD audio) ⇒ Speaker output.
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (PCM, DolbyDigital, DTS) ⇒ HDMI output (audio output from connected TV)
( b The input source can be switched to any source except CBL/SAT.)
・ GUI display ⇒ HDMI output.
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (ZONE2 Function) ⇒ HDMI output (ZONE2)
( b The input source can be switched to any source except CBL/SAT.)