Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nordic BAS-L0118
Summary of Contents for Nordic BAS-L0118
- Page 1 18V CORDLESS BANDSAW OPERATING MANUAL BAS-L0118...
-
Page 2: Product Specification
NORDIC PRODUCT SPECIFICATION Voltage: 18V DC Rated Speed: 0-2m/s Blade Size: 165mm Max Cutting Capacity: ø 127mm Vibration: 6.143m/s , K=1.5m/s A weighted sound pressure level: LpA: 77.1dB(A) ; KpA=3dB(A) A weighted sound power level: LwA: 88.1dB(A) ; KwA=3dB(A) GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions. -
Page 3: Electrical Safety
NORDIC 2.2 ELECTRICAL SAFETY • Always check that the power supply corresponds to the voltage on the rating plate. • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed power tools. -
Page 4: Dust Protection
NORDIC 2.4 POWER TOOL USE AND CARE • Do not expect the power tool to do more than it can. Use the correct power tool for what you want to do. A power tool will achieve better results and be safer if used in the context for which it was designed. -
Page 5: Prevent Burning
NORDIC SAW BLADE SAFETY Use the correct size and style of blade. Inspect blades for cracks and missing teeth before each use. Do not operate with dull, cracked or badly worn blade. When replacing blades, make sure the blade teeth are pointing down and towards the table. -
Page 6: Vibration Safety
NORDIC Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. -
Page 7: Additional Safety Instructions For Batteries And Chargers
NORDIC WARNING: To avoid electrocution, DO NOT use in wet or damp areas or expose to rain. ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS Use only batteries and chargers applicable for this machine. 4.1 BATTERIES • Never attempt to open for any reason. - Page 8 NORDIC SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury or damage to the tool. Read manual before use Wear eye protection Wear ear protection Wear safety gloves In accordance with essential requirements of the European directive(s) Class II - The machine is double insulated;...
-
Page 9: Before You Start
NORDIC BEFORE YOU START BATTERY CHARGER The lithium-ion battery can be charged at any time and will not develop a “memory” when charged after only a partial discharge. It is not necessary to run down the battery pack charge before recharging. Remove the battery pack from the tool when convenient for you and your job. - Page 10 NORDIC INSTALLING/REMOVING SAW BLADE Your band saw is designed to fit saw blades 44-7/8” long, 1/2” wide and 0.025” thick. Use the correct- sized blade that is suitable for the material to be cut. A 10/14 TPI saw blade which is included with your saw (pre-installed).
-
Page 11: To Remove The Blade
NORDIC TO REMOVE THE BLADE: Make sure the saw is switched off and the power is disconnected. Turn the tension handle (Fig. 1 - 1) clockwise to release blade tension. Wearing work gloves and safety goggles, carefully slide the blade off the top of the guide wheels and remove it from the guide bearings. -
Page 12: Cleaning And Maintenance
NORDIC To start a cut, use minimal force to guide the blade into the workpiece to create a groove. Then, allow the rest of the blade to cut into the workpiece. Guide the tool to prevent blade from moving from side-to-side during cutting.
Need help?
Do you have a question about the BAS-L0118 and is the answer not in the manual?
Questions and answers