Table of Contents
Advertisement
Quick Links
X532
MODEL V20A
POLE MOUNTING ADAPTER
Copyright © 1998 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
Vicon Part No. 8006-8532-01-00 Section 7 Rev 998
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TELEPHONE: 516-952-CCTV (2288) FACSIMILE: 516-951-CCTV (2288)
TOLL FREE: 800-645-9116 UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207
Advertisement
Table of Contents
Related Manuals for Vicon V20A
Summary of Contents for Vicon V20A
- Page 1 Copyright © 1998 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. Vicon Part No. 8006-8532-01-00 Section 7 Rev 998 VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788...
- Page 3 We stand behind the quality and dependability of every product with an industry leading Beneficial Use warranty. If you are not satisfied with a Vicon product or service, I would like to know. Your complete satisfaction is the mission of every Vicon employee.
-
Page 5: Table Of Contents
Inspection For Concealed Damage ....................... 3 Installation Preparation ........................3 Bracket-to-Plate Installation......................... 4 Plate-to-Pole Installation ........................5 Extending the Chain Length ........................ 7 Maintenance ............................7 Shipping Instructions........................8 Technical Information ........................9 Contents • • i X523 Rev 998 V20A Pole Mounting Adapter... - Page 6 Installing the Pole Mount Brackets to the Pole Adapter Plate..............5 Figure 2 Pole Mounting Adapter Assembly Installation..................6 Figure 3 Connecting Chain Link Installation ......................7 ii • • List of Figures X523 Rev 998 V20A Pole Mounting Adapter...
-
Page 7: Introduction
Designed to be installed on a pole with a minimum diameter of 3 inches (7.6 cm) and a maximum diameter of 10 inches (25 cm), the V20A with a wall mount attached can support a complete camera system, including a dome system or a pan-and-tilt drive and camera housing with camera, up to the load rating of the particular wall mount being used. -
Page 9: Installation
Before beginning installation, run all necessary cabling to the location selected for the installation. The V20A Pole Mounting Adapter has a variety of mounting holes to accommodate a variety of Vicon mounts, pan-and-tilt drives, scanners and housings. The V20A consists of a pole adapter plate, two pole mount brackets, an 18- and 24-inch chain (with two tension nuts and brackets and extension links), two hex-head bolts and eight Installation •... -
Page 10: Bracket-To-Plate Installation
2. If it is appropriate at this time, mount the selected wall mount to the pole adapter plate. Refer to the instruction manual for the particular wall mount for installation instructions. 4 • • Installation X523 Rev 998 V20A Pole Mounting Adapter... -
Page 11: Plate-To-Pole Installation
(provided) into the hole. Plug any unused fitting. Refer to the instruction manual for the wall mount and the equipment at the camera station of cabling instructions. Installation • • 5 X523 Rev 998 V20A Pole Mounting Adapter... - Page 12 Figure 2 Pole Mounting Adapter Assembly Installation 6 • • Installation X523 Rev 998 V20A Pole Mounting Adapter...
-
Page 13: Extending The Chain Length
Strike all four pins with a small hammer to set the pins, making sure the link can not come apart. Figure 3 Connecting Chain Link Installation Maintenance Model V20A does not require any maintenance. Maintenance • • 7 X523 Rev 998 V20A Pole Mounting Adapter... -
Page 14: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 15: Technical Information
3 - 10 inches (7.6 - 25 cm). Dimensions: Height: 12.4 in. (31.5 cm). Width: 9.5 in. (24.1 cm). Depth: 3.9 in. (9.9 cm). Weight: 15.0 lb (6.8 kg). Construction: Steel. Finish: Light gray paint. Technical Information • • 9 X523 Rev 998 V20A Pole Mounting Adapter...
Need help?
Do you have a question about the V20A and is the answer not in the manual?
Questions and answers