Vicon V896MA Installation & Operation Manual

Mounting adapter for the v896msh maximum security housing

Advertisement

X819-03-01
MODEL V896MA
MOUNTING ADAPTER FOR THE
V896MSH MAXIMUM SECURITY
HOUSING
Copyright © 2002 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266
UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com
Vicon part no. 8006-8819-03-01
Rev 102 Section 6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V896MA and is the answer not in the manual?

Questions and answers

Summary of Contents for Vicon V896MA

  • Page 1 Copyright © 2002 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266 UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com...
  • Page 3 Introduction • • 3 X819-03-01 Rev 102 V896MA Mounting Adapter...
  • Page 4: Installation

    The V896MA Mounting Adapter is used when the V896MSH Maximum Security Housing is to be mounted to a vertical surface, like a wall or square pole. Before installing the V896MA, refer to Instruction Manual X795 for the installation of the V896MSH housing and observe all Notes, Cautions and Warnings listed there.
  • Page 5 1/4-inch lag bolts, at least 2-1/2 inches long. Note: If it is necessary to mount the V896MA to a round pole, special hardware is required. 12. Close off the four (4) mounting holes normally used for ceiling mounting with four (4) 1/4-20 screws, nuts, and sealing washers supplied for the housing to be water resistant.
  • Page 6 Figure 1 Exploded View 6 • • Installation X819-03-01 Rev 102 V896MA Mounting Adapter...
  • Page 7: Maintenance

    Figure 2 Figure 3 Housing Base Plate/Gasket Dimensional Drawing Maintenance Model V896MA does not require any maintenance. Refer to Instruction Manual X795 for maintenance of the V896MSH housing. Maintenance • • 7 X819-03-01 Rev 102 V896MA Mounting Adapter...
  • Page 8: Shipping Instructions

    Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A.
  • Page 9: Technical Information

    Cable Access: Hole provided for routing cable. Dimensions: Height: 6.63 in. (16.8 cm). Width: 3.0 in. (7.6 cm). Weight: 2.9 lb ( 1.3 kg). Construction: Steel. Finish: Dark gray. Technical Information • • 9 X819-03-01 Rev 102 V896MA Mounting Adapter...
  • Page 10 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) &Infofax: 800-287-1207 Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom 44/(0) 1489/566300 Fax: 44/(0) 1489/566322 Brussels Office Planet II - Unit E...

Table of Contents