Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for XO Appliance XOE2
Summary of Contents for XO Appliance XOE2
- Page 2 When buying any XO appliance, you can be con you have chosen a high quality, innovative and stylish product from a company that cares about you! If you require service or have questions, there are 2 ways to contact our ventilation experts;...
-
Page 3: Where Things Are
where things are 4 - 11 GETTING READY Safety and Precautions Overall Dimensions Install Examples Mounting Height Planning Ductwork THE INSTALL 13 - 21 Vented or Recirculating Installation Mounting Dimensions Installing Electrical Connections OPERATING & MAINTENANCE Push Button Controls Maintenance TROUBLESHOOTING Common Questions &... -
Page 4: Safety First
safety first IMPORTANT SAFETY INSTRUCTIONS FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. -
Page 5: Installation Instructions
greasy spillovers that may ignite. Heat oils slowly on low or medium settings. B. Always turn hood ON when cooking at high heat. C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. D. Use proper pan size. Always use cookware appropriate for the size of the surface element. - Page 6 code authorities. C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. D. Ducted fans must always be vented to the outdoors. E. This unit must be grounded. WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE DANGEROUS.
-
Page 7: Before You Begin
before you begin You will need some simple tools. Take time to plan your work. If you are venting the hood outside - follow the guide lines in this book to minimize the length and turns of your dutwork and maximize performance. DANGER:If installing above a gas appliance - turn gas off at the source before installing or servicing this appliance. - Page 8 dimensions 12” (305mm) 29-7/8” (758mm) 5-7/8” 14-7/32” (150mm) (361mm) 19-11/16” (500mm) FRONT REAR - 8 -...
-
Page 9: Typical Installation Examples
typical installation examples WALL EXHAUST ROOF EXHAUST BUILT-IN FRONT EXHAUST VENT RECIRCULATION EXHAUST MUST BE RETURNED TO THE SPACE - 9 -... -
Page 10: Highs And Lows
highs and lows RECOMMENDED MOUNTING HEIGHT ABOVE COOKING SURFACE ELECTRIC 20” - 32” 24” - 32” All range hoods have a recommended range of installation height over the cooking surface. It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard;... - Page 11 a few simple rules to plan your ductwork THIS HOOD IS DESIGNED TO USE A 6” or 7” ROUND DUCT - IT MAY BE TRANSITIONED TO A 3-1/4” X 10” RECTANGULAR DUCT NEVER REDUCE DUCT SIZE. UNDERSIZED DUCTING SEVERELY RESTRICTS AIR FLOW AND HARMS PERFORMANCE.
- Page 12 estimating total equivalent feet in a duct CAUSING AIR TO CHANGE DIRECTION CAUSES TURBULENCE AND RESTRICTS FLOW IN A SYSTEM. IF USING FLEXIBLE METAL DUCT - INCREASE ALL MULTIPLIERS BY 50% (12 BECOMES 18 - ETC.) THIS EASY TO USE WORKSHEET IS FOR 600 CFM OR LESS. UNDER “QTY USED”...
-
Page 13: Vented Installation
vented installation STEP 1. After unboxing, remove both stainless steel filters by pulling on the latches as shown. REMOVE THESE 6 SCREWS STEP 2. Remove the inner cover by removing the 6 screws indicated in red. STEP 3. Remove the accessory box. - Page 14 vented installation cont. STEP 4b. If you are top venting using a 3-1/4” x 10” rectangular duct, remove the rectangular top plate but DO NOT REMOVE the half round knock out plate. Use 2 screws to attach the rectangular duct adapter.
- Page 15 recirculation (ductless) STEP 1. After unboxing, remove both stainless steel filters by pulling on the latches as shown. REMOVE THESE 6 SCREWS STEP 2. Remove the inner cover by removing the 6 screws indicated in red. STEP 3. Remove the accessory box.
- Page 16 recirculation (ductless) cont. STEP 5. Remove the plate covering recirculating vent on the top, front center of the hood. RECIRCULATING VENT IMPORTANT NOTE: For cabinets deeper than 12” The Recirculating Vent cannot be restricted in operation. If the cabinet above is more than 12” deep, mount the hood farther out from the wall ensure the vent is clear.
-
Page 17: Hood Installation
hood installation CAUTION: TEAM LIFT - To prevent injury and/or damage to the unit use two or more people to lift, carry or hold the hood in place while it is being secured. CAUTION: If venting outside, ensure the ducting is unobstructed, and the damper is operating freely. - Page 18 hood installation cont. USEFUL DIMENSIONS: 29-11/16” 2-5/16” 1-3/4” 4-5/8” 7-7/8” 10-3/16” FRONT TOP VENT - ROUND DUCT LOCATION 7” Dia. FRONT - 18 -...
- Page 19 hood installation cont. TOP VENT - RECTANGULAR DUCT LOCATION 14-15/16” 1-3/16” 3-1/4” x 10” 3/4” 4-5/8” 3/4” FRONT REAR VENT - RECTANGULAR DUCT LOCATION 3-1/4” x 10” REAR - 19 -...
-
Page 20: Electrical Connection
electrical connection Your XOE unit come pre-wired with a 3 prong cord set. However, if you wish to hardwire the hood instead - follow these steps. 1. Route the power cord to the junction box inside the hood. 2. Using listed conduit fittings and connectors, use the internal wire clamp to secure the wiring entering the hood. - Page 21 hood installation cont. Step 8. Lift the hood into place, aligning the duct if venting, exercising care not to pinch electrical wiring. Fasten in place with 6 screws as shown here. Center 2 screws optional for added support. If venting check dampers for free operation and tape seal all duct joints.
-
Page 22: Easy To Maintain
easy to operate Your new XO Hood is easy to operate with 5 illuminated, electronic touch sensor buttons. 0 - Turns the unit on and off, hold this button for 2 seconds and it will initiate the 5 minute time delay feature. 1 - Activates low speed 2 - Activates medium speed 3 - Activates high speed... -
Page 23: Troubleshooting
trouble shooting HOOD WILL NOT OPERATE: Check to see if the power supply is connected properly. Is the power turned on at the breaker / fuse box? Check wiring between the switch and control board. HOOD VIBRATES WHILE RUNNING: Is the hood secured properly to the wall / cabinet? Is the blower motor securelty fastened? Is the fan damaged and out of balance? HOOD IS NOT MOVING MUCH AIR:... - Page 24 we’ve got your back 90 DAY LOVE IT or LEAVE IT. For 90 Days all our products are backed by our unique Love it or Leave it Guarantee. ONE-YEAR PARTS & LABOR LIMITED WARRANTY. XO warrants to the original purchaser of this new XO ventilation unit, the cabinet and all parts thereof, to be free from defects in material or workmanship under normal and proper use and maintenance as specified by XO and upon proper installation and start-up in accordance with the instruction packet supplied with each XO unit.