Advertisement
How to use control panel
Height Adjustment Function:
If the LED display shows the current height, long press "
button can adjust the table height.
Height Memory Function:
Click "M" button and LED display shows "
from " ", " ", " 3 ", " 4 " to achieve the height setting. In the
meanwhile, the light flickers meaning the data has been successfully
saved. Click the corresponding button and then the desk can be
adjusted to the saved height.
Reset Function:
1. When the height is different with the LED display or it shows the
default code, you need to reset the desk.
2. Press and keep "
" button to adjust the desk until it goes down
to the lowest place. Then long-press the "
5s to enter the reset process and LED display shows "
long-press the "
" button until it bounces up and the LED display
shows the current height, which means the reset is a success.
Anti-Collision Sensitivity Adjustment:
1. Press and hold the "
" and "
time for 5s to switch the sensitivity, one operation to switch one level,
divided into 4 levels,
,
,
2. The display shows "
" means the anti-collision function is
closed; the display shows "
" means high sensitivity; the display
shows "
" means medium sensitivity; the display shows "
means low sensitivity.
3. When the desk goes up or down, it will rebound immediately when
encountering obstacles to prevent itself.
The following tips will help you detected and eliminate the common fault and
error. If the fault you met is not listed below, please contact 1300 OFFICE
(1300 633 423). Only the manufacturer and professionals are capable for
investigating and correcting those fault and error.
Error Code
Description
E01
Overwork
Overtemperature
E02
Overloaded
E03/E04
The legs cannot move in the process of
E05/E06/E10
rising or going down
E07/E08/E20/E21/E22//E23
All the cables be connected well
E09
The weight distribution on two sides of table
is severely unbalanced.
"or "
". Then click any button
"button for more than
" . Then
" buttons together at the same
,
.
"
Method
Please retry 18 mins later
Please retry 18 mins later
Please reset
Please reset
Please reset
Please reset
Button
"
LED Display
Button introduction
Button 'stand'. suitable for standing, the first height data saved by users
Button 'sit'. suitable for standing, the second height data saved by users
Function key, use with other buttons
Position 3, the third height data saved by users
Position 4, the third height data saved by users
Upper button, adjust the desk to rise
Downward button, adjust the desk to go down
Code Processing:
1. When the LED display shows "
function.
2. If "E01" or "E02" appears, please let the desk reset for more than 13
minutes before it can be used normally.
3. If other codes appear and there is no response after pressing the
"
"button, please make sure that the cable is not damaged and the
connection is normal, and power off for more than 10 seconds, then
turn on the power again, "
button to reset.
4. If the above operations are performed, the table still does not
operate normally, please contact customer service.
1. Power supply: AC100V-240V, 50/60Hz
2. Service Environment: 0-40
3. Unplug the power plug before cleaning, wipe the dust on surface with slight
wet dishcloth when cleaning, be careful not to let the drops into the internal
parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc.,
so dispose of it in accordance with each country's environmental legislation, not
the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first
use.
7. Children are forbidden to play on the product because of unforeseen action
when playing, so any dangerous consequences caused by this improper action
will not be on manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will
not have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must
ensure that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without
supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environ-
ment. e.g., do not litter the tools around. Always be careful to treat the
packaging materials in order to avoid any possible danger, e.g. plastic bag may
lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the
future use in transportation.
17 / 18
", please refer to the reset
" is displayed, then long-press the "
"
Advertisement
