ABB HT613221 Operation Manual page 182

Operation Manual / A150-M58/68
Tables
Tables
Table 1: Definition of pictograms ............................... 9
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table 4: Weight of complete turbocharger unit .... 29
Table 5: Torque-controlled tightening of the pres-
sure screws .................................................................... 37
Table 6: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 44
Table 7: Lubricating oil temperature at the inlet ... 45
Table 8: Maximum lubricating oil temperature at the
outlet .............................................................................. 45
Table 9: Tightening torque (86505).......................... 49
Table 10: Expected replacement intervals .............. 55
Table 11: Maintenance table ....................................... 58
Table 12: Parameters for wet cleaning of com-
pressor ............................................................................ 61
Table 13: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 64
Table 14: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 65
Table 15: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 66
Table 16: Value table for soaking .............................. 74
Table 17: Malfunctions when starting - Delayed
start-up ........................................................................... 77
Table 18: Malfunctions when starting - Vibrations 77
Table 19: Malfunctions when starting - Rubbing of
rotating parts................................................................. 77
Table 20: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 78
Table 21: Malfunctions during operation - Speed re-
duces............................................................................... 78
Table 22: Malfunctions during operation - Speed in-
creases ........................................................................... 78
Table 23: Malfunctions during operation - Exhaust
gas temperature too high .......................................... 79
Table 24: Malfunctions during operation - Charge air
pressure too low........................................................... 79
© Copyright 2022 ABB. All rights reserved.
Table 25: Malfunctions during operation - Charge air
pressure too high .......................................................... 80
Table 26: Malfunctions during operation - Engine
performance losses....................................................... 80
Table 27: Malfunction - Turbocharger surging........ 81
Table 28: Malfunction - Sporadic surge blows ........ 81
Table 29: Malfunctions when stopping - Runout
noises ............................................................................... 82
Table 30: Malfunctions when stopping - Runout
time too short ................................................................ 82
Table 31: Malfunction of the speed measurement
system - No signal or poor signal amplitude .......... 83
Table 32: Malfunction of the speed measurement
system - Measured speed too high ........................... 83
Table 33: Malfunction of the speed measurement
system - Measured speed too low............................. 83
Table 34: Swivel lifting eyes......................................... 85
Table 35: Press-off screws ........................................... 86
Table 36: Dismantling screw ....................................... 86
Table 37: Weights of assemblies ................................ 91
Table 38: Tightening torques ...................................... 92
Table 39: Tightening torques for insulation ............ 93
Table 40: Press-off screws - gas outlet flange........ 98
Table 41: Tightening torque (90012-01) .................. 102
Table 42: Permissible clearances A and B ............... 107
Table 43: Nozzle ring compression PD .................... 108
Table 44: Tightening torque (90012-01) .................. 111
Table 45: Tightening torque (51007) ........................ 112
Table 46: Tightening torque (79041) ........................ 113
Table 47: Tightening torque (72011) ........................ 114
Table 48: Permissible clearances N and R................ 117
Table 49: Tightening torque (51009)....................... 120
Table 50: Tightening torque (51009)........................ 121
Table 51: Tightening torque (72051) ........................ 123
Table 52: Permissible clearances A and B ................ 131
Table 53: Nozzle ring compression PD .................... 132
HZTL4041_EN Revision F February 2022