Download
Share
Print this page
Intermec EasyCoder PD41 Instructions Manual
  1. Manuals
  2. Brands
  3. Intermec Manuals
  4. Printer Accessories
  5. EasyCoder PD41
  6. Instructions manual

Intermec EasyCoder PD41 Instructions Manual

Easylan ethernet software
Hide thumbs Also See for EasyCoder PD41:

Advertisement

Quick Links

See also: Service Manual , User Manual
Instructions
EasyLAN Ethernet
Software
for the EasyCoder®
PD41 and PD42 Printers

Advertisement

loading

Related Manuals for Intermec EasyCoder PD41

Summary of Contents for Intermec EasyCoder PD41

  • Page 1 Instructions EasyLAN Ethernet Software for the EasyCoder® PD41 and PD42 Printers...
  • Page 2 The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation.

  • Page 3: Table Of Contents

    Introduction ........5 Printer Firmware Requirements..... . .5 Setting Network Parameters from the Printer Home Page .
  • Page 4 EasyLAN Ethernet Software Instructions...

  • Page 5: Introduction

    Printer Firmware Requirements Before you begin, confirm that the printer is running either Intermec Fingerprint v10.x.x or IPL v10.x.x firmware. If you have a PD41 printer, the easiest way to check the firmware version is to print a test label (for help, see the...

  • Page 6: Setting Network Parameters From The Printer Home Page

    You can change all network parameters by using your web browser to access the printer home page. To access the home page, you need the IP address of the printer. As a default setting, the printer is set to automatically receive an IP address from the...

  • Page 7: Setting Network Parameters With Printset 4

    Setting Network Parameters with PrintSet 4 PrintSet 4 is a PC-based software application that lets you configure your Intermec printer from your computer. The program is available on the PrinterCompanion CD, and can also be downloaded from the Intermec web site.

  • Page 8: Setting Network Parameters With Fingerprint And Ipl Commands

    Dump mode can be entered through Testmode and Extended Testmode, for help see the EasyCoder PD41 Printer User’s Guide (1-960652-xx) or the EasyCoder PD42 Printer User’s Guide (934-009-xxx).
  • Page 9 SETUP "NETWORK,DEFAULT ROUTER,192.168.236.1" SETUP "NETWORK,NAME SERVER,255.255.78.120" Once you have set the parameters above you can use your web browser to access the printer home page and make the rest of your changes there. Setting Network Parameters with IPL commands If your printer is running IPL firmware, you can modify various...

  • Page 10: Setting Ip Address Using Arp'n'ping

    <STX><SI>n192.168.235.86, 255.255.255.0, 192.168.236.1<ETX> Once you have set the parameters above you can use your web browser to access the printer home page and make the rest of your changes there. Setting IP Address Using ARP’n’PING Use the ARP’n’PING method to set the printer IP address if your network does not have a DHCP or BOOTP server.
  • Page 11 3 Next, use Ping to make the printer set the IP address: ping IP address 4 Exit the Command Prompt. EasyLAN Ethernet Software Instructions...
  • Page 12 Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com EasyCoder PD41/PD42 EasyLAN Ethernet Software Instructions *943-130-001* P/N 943-130-001...

This manual is also suitable for:

Easycoder pd42