Oven Light; Oven Door - GE PTS9000 Owner's Manual

Oven Light

SHOCK OR BURN HAZARD: Before replacing oven light bulb, disconnect the electrical power to the
WARNING
oven at the main fuse or circuit breaker panel. Failure to do so may result in electric shock or burn.
BURN HAZARD: The glass cover and bulb should be removed when cool. Touching hot glass with
CAUTION
bare hands or a damp cloth can cause burns.
1. Disconnect power at the main fuse or circuit breaker
panel.
2. Remove oven racks.
3. Slide a flat blade screwdriver or butter knife between
the metal housing and the glass light cover.
NOTE: on some models there is a metal clip visibly
holding the glass. The tool needs inserted between
the metal housing and the clip holding the glass.
4. Support the glass light cover with two fingers to prevent
the cover from falling to the bottom of the oven.
5. Gently twist the screwdriver blade or butter knife to
loosen the glass light cover. Be careful not to chip
the oven coating.

Oven Door

The door is very heavy. Be careful when removing and lifting the door. Do not lift door by the handle.
Before removing the door, disconnect the camera harness by unhooking the connector that is snapped
into the bottom of the door.
Oven Door Removal
NOTE: Door removal is not a requirement for installation
of the product but is an added convenience.
To remove the door:
1. Open the oven door as far as it will go.
2. Push both hinge locks down toward the door frame to
the unlocked position. This may require a flat-blade
screwdriver. DO NOT LIFT THE DOOR BY THE
HANDLE!
Hinge
Slot
Hinge
Arm
3. Place hands on both sides of the door and close the
oven door to the removal position (approximately
1"–2" [2.5 cm–5.1 cm] from the closed position).
4. Lift the door up and out until
the hinge arms clear the
slots. NOTE: The oven door
is very heavy. Be sure you
have a firm grip before
lifting the oven door off the
hinges. Use caution once the door is removed. Do
not lay the door on its handle. This could cause dents
or scratches.
22
Hinge Unlocked
Position
Hinge Clears Slot
6. Remove the glass light cover.
7. Remove the bulb by firmly grasping and sliding the
bulb straight out until the two prongs have cleared
the ceramic holder.
8. Do not touch the glass of the new replacement bulb
with your fingers. It will cause the bulb to fail when it
lights. Grasp the replacement bulb with a clean towel
or facial tissue with the prongs facing down. Align
the two prongs in the ceramic holder, pressing gently
until the bulb is securely in the ceramic socket.
9. Slide the protective lens into the holder and push
until the clips snap into the housing.
10. Reconnect power.
Replacing the Oven Door
NOTE: The oven door is heavy. You may
need help lifting the door high enough to
slide it into the hinge slots. Do not lift the
door by the handle.
1. Lift the oven door by grasping each
side.
2. With the door at the same angle as
the removal position
(approximately 1"–2" [2.5
cm–5.1 cm] from the closed
position), seat the notch
of the hinge arm into the
bottom edge of the hinge
slot. The notch of the hinge
arm must be fully seated
into the bottom of the slot.
3. Fully open the door. If
the door will not fully
open, the indentation is
not seated correctly in
the bottom edge of the
slot.
4. Push the hinge locks up
against the front frame
of the oven cavity, to the locked position.
5. Close the oven door.
Hinge
Bottom
Arm
Edge of
Slot
Hinge Notch
Hinge in
Locked
Position
Notch of Hinge
Securely Fitted
Into Bottom of
Hinge Slot
49-2000376 Rev. 4