Advertisement
Quick Links
Advertisement
Related Manuals for Cooke & Lewis CLFLEXDOWN
Summary of Contents for Cooke & Lewis CLFLEXDOWN
- Page 1 Induction Booster Induction Booster Flexi-zone Flexi-zone 5059340127514 CLFLEXDOWN...
- Page 2 EN Contents Preparation Installation Care and Maintenance...
- Page 3 Installation EN IMPORTANT - Please read carefully the separate safety guide before use. 4 x 15mm Not included 3663602637462 3663602843153 3663602480044 BASE CABINET 80cm VENT PACK (Ø150mm) BASE CABINET 100cm RECIRC KIT 1...
- Page 4 Preparation VENT PACK (Ø150mm) VENT PACK (Ø150mm) CARBFILT 50 Choose a type of installation: Ducted option A (extraction to the outside) or Recirculation option B (no extraction to the outside). This appliance is for installation in a 80cm or 100cm base cabinet only.
- Page 5 Preparation Use the following instructions to modify your base cabinet (not supplied) to fit the appliance.
- Page 6 Preparation Base Cabinet Modification (x1) (x1) (x7) (x10) (x7) (x1) 50mm 15mm 20mm (x2) (x2) (x5) (x6) 15mm 30mm (x2) (x3) (x5) (x37) (x3) (x5) (x5) (x2) (x2) Check the base cabinet parts and identify the pieces to be modified. Note: *CC is to be modified if you have chosen Recirculation Option B.
- Page 7 Preparation These dimensions are for a 38mm worktop, measure, mark and cut panels HH and GG as required. Adjust cutting dimensions for different worktop thicknesses (see table above).
- Page 8 Preparation (x7) (x7) (x10) 20mm (x2) (x1)
- Page 9 Preparation 20mm (x2) (x1)
- Page 10 Preparation 20mm (x2) (x1) 50mm (x 3)
- Page 11 Preparation [0 3] X 2 [04] X 4 [04] X 4 280mm...
- Page 12 Preparation 90° [x2] (x20) 15mm (x5) (x5)
- Page 13 Preparation 150mm 28mm 150mm Caution! Before drilling it is extremely important to check the wall for hidden pipes, electrical cables etc using an appropriate detection device. Warning: Good ventilation is required around the appliance for easier dissipation of heat and low power consumption.
- Page 14 Preparation 770mm 520mm 285mm 45mm 750mm 490mm >5mm <200mm Ø150 Cut an aperture in the worktop using a jigsaw as shown. The worktop should be at least 12.5mm thick and made of a heat resistant material. IMPORTANT: Please see "Cleaning the Lower Tray and Extractor Grill" in the Care & maintenance section later in this manual.
- Page 15 Preparation Seal the cut edge of the worktop using silicone sealant or PVA adhesive. IMPORTANT: ensure that either product is fully cured as per the manufacturers instructions before you commence installation of the hob. This hob MUST NOT be sealed into the worktop.
- Page 16 Preparation Stretch out and stick the supplied tape along the underside edge of the hob, ensuring the ends overlap. Trim off any excess tape and dispose of it.
- Page 17 Preparation Once the worktop edge has cured, and the tape is fitted, position the hob into the cutout in the worktop. Apply gentle downwards pressure onto the hob to push it into the worktop ensuring a good seal around the outer edge.
- Page 18 Preparation Electrical Installation All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. Direct Connection This appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between contacts.
- Page 19 Installation Installation Caution: This appliance must be installed by a qualified person in compliance with the instructions provided. The manufacturer declines all responsibility for improper installation, which may harm persons and animals and cause damage. • This appliance must not be installed directly above a dishwasher, fridge, freezer, washing machine, oven or clothes dryer as the humidity may damage the hob electronics.
- Page 20 Installation EN Only for ducted option. EN Only for recirculation option. RECIRC KIT 1...
- Page 21 EN Use Before you start WARNING: Read the instructions before using the appliance. When the power is switched on at the isolation switch, the hob will beep once and the display will be blank for a few seconds before 3 dots appear indicating that the software is initiating. Once the process is complete the display will show an initial date and time, the appliance is now ready for system set up.
- Page 22 EN Use Do not use cookware with jagged edges or a curved base. Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Use pans whose diameter is as large as the graphic of the zone selected. You will get maximum efficiency by matching the pan size to the cooking zone and ensuring it is central.
- Page 23 EN Use The default shutdown times are shown in the table below: Power level The heating zone shuts down automatically after 6 hours 3 hours 2 hours 90 minutes The hob will automatically switch off after one minute once the pan has been removed from the cooking zone. Detection of Small Articles If the hob detects an unsuitable pan or small article (e.g.
- Page 24 EN Use Description of the control keys Control panel for cooker hood Control panel for induction hob...
- Page 25 EN Use Reference Description Zone select key Child lock key ON/OFF key Boost control key/Keep warm key Timer key/Pause key（For induction hob） Power/Timer regulating key(reduce) Power/Timer regulating key(increase) Grease filter clean reminder function Delay shutdown function button key Auto mode combination key...
- Page 26 EN Use Using your induction hob 1. Touch and hold the On/Off control. The hob will beep once and the zones will show to indicate it is on standby “-” mode. Note: If you do not select a cooking zone and power level within one minute, the hob will switch off automatically. 2.
- Page 27 EN Use Using the flexible zones The left zones and right zones can be used individually at the front or the rear, or be configured to work as a flexible zone When configured as a flexible zone, the front and rear areas are linked and can be controlled with one power setting. As before, ensure that the pans are placed correctly on the selected cooking zone.
- Page 28 EN Use Safety mode (Child lock) You can lock the controls to prevent unintended use by children. When the controls are locked, all the controls except the OFF control are disabled. To lock the controls Touch the key for 3 seconds, the timer indicator will show "Lo". To unlock the controls 1.
- Page 29 EN Use Using the timer You can set the timer from 1-99 minutes and this can be used in two ways: 1. As an alarm that does not alter any of the cooking zones. 2. As an automatic switch off function to turn off a cooking zone. Note: This function only operates on one zone at a time;...
- Page 30 EN Use Controlling the extractor fan 1.Touch and hold the ON/OFF key . After power on, the buzzer beeps once, all displays show “ - “, indicating that the cooker hood has entered the state of standby mode. 2.Select the power level by pressing the key or key 3.The power level will start at "0".
- Page 31 EN Use Auto mode combination 1. Under the condition of the whole machine running, click the key and key 3 seconds at the same time. 2. After 3 seconds, the display of the Cooker Hood shows "A" and flashes 5 seconds. After 5 seconds, the display stops flashing.
- Page 32 Care & maintenance WARNING: Always switch off the electricity supply before performing maintenance work. In the event of a fault, contact customer services. Cleaning the Lower Tray and Extractor Grill IMPORTANT: Empty the lower tray regularly to avoid overflowing!
- Page 33 EN Care & maintenance Cleaning the Aluminium Grease Filters When the cooker hood reaches a cumulative working time of 50 hours a reminder to clean the grease filter will be activated. The display will show " " and flash red to advise you to clean the grease filters . After cleaning the filters, reset the alert by pressing the Icon...
- Page 34 EN Care & maintenance Carbon filter replacement Replace the carbon filter every 3-6 months, however it is recommended to wash the magnetic grill [10] and carbon filter case [09] every 3 months, do not wash the carbon filter. [10] 3-6 MONTHS [09]...
- Page 35 EN Care & maintenance Damaged power cables should be replaced by a If the surface of the hob becomes cracked, do competent person or qualified electrician. not use, switch off the appliance at the fused spur and contact customer services. For domestic use only.
- Page 36 EN Care & maintenance If your hob develops a fault In the event of a fault, the induction hob will automatically enter a safety mode and diagnose the likely issue. The most common error codes are shown below. Error Possible Cause What to do No pot or pot not suitable Choose the suitable pan...
- Page 37 Addresses Manufacturer • Fabricant • Producent • PL Dystrybutor: Producător: UK Manufacturer: Castorama Polska Sp. z o.o. ul. Kingfisher International Products Limited, Krakowiaków 78, 02-255 Warszawa 3 Sheldon Square, London, W2 6PX, www.castorama.pl United Kingdom Aby zapoznać się z instrukcją www.kingfisher.com/products obsługi online, odwiedź...