Page 1
Ultrak 4 9 9 INSTRUCTION MANUAL FEATURES: FIG. 1 CHRONOGRAPH • 2000 memories • Segregated memory (capability to memorize LAP times of different races) • User Selectable LAP/SPLIT or LAP/SPEED display • Average and best lap time display • Automatic release of LAP time after 10 seconds to allow progress monitoring.
CHRONOGRAPH OPERATION Press C to go to the CHRONOGRAPH MODE. The display as shown in Fig. 2. Press A to start. Fig. 2 Press B to get the 1st LAP time. The LAP time is shown at the top row, the SPLIT time at the middle row and the running total time is shown at the lower row, as shown in Fig.3.
Page 3
Press B to display the 2nd LAP time. Fig. 5. Press A to stop. Fig. 6. Press B to reset and be ready for the next race, as shown in Fig. 7. The counter at the top left corner displays the memory left for further races. Further races can be recorded by pressing A and B buttons as above.
Page 4
Press D to recall data stored. The display which we call the RACE RECORD is as shown in Fig. 8. The display shows the date in which the race was recorded and MCH-001 (MSP for SPEED mode) stands for the first race recorded in LAP/SPLIT mode at that date.
Page 5
Press D to recall the 2nd LAP data, as shown in Fig.10. Fig.10. Press D again shows the stopped time, Fig. 11. Fig.11. Press D again to show the average LAP time, as shown in Fig.12. Fig.12.
Page 6
Press D again to show the Best LAP time, as shown in Fig.13. Fig.13. ** The AVERAGE calculation and BEST record do not take into account the last section of time before STOP. Therefore, in order for the stopwatch to keep track of the average and best records of all Laps, always use the B button until the end of the race.
Page 7
Press A to start, the display is as shown in Fig.16. Fig.16. Press B to get the 1st LAP time at the top row and the speed at the middle row, as shown in Fig.17. If for example the distance is set to 200 meters and time unit set is in seconds, the speed calculated from a LAP time of 17.09 seconds is 11.70 m/sec.
TIMER OPERATION Press C button until the stopwatch goes to the TIMER mode. The display is as shown in Fig.18. The top row is the display for the 1st timer and the middle row is the display for the 2nd timer. Fig.18.
PRINT MODE Press C button to go to the PRINT ALL mode as shown in Fig.20. Pressing A button will print all recorded memories to the printer (if printer is connected). When the stopwatch is in the process of printing, an indicator moves from right to left. When printing is complete PRINT END is displayed.
UPLOAD MODE In Fig. 20 press D button once will switch to UPLOAD MODE as shown in Fig.22. Pressing A button will UPLOAD ALL recorded memories to computer (if computer is connected). When the stopwatch is in the process of uploading, an indicator moves from right to left.
Page 11
TIME Press C to go to the TIME MODE. The display is as shown in Fig.24. Fig.24. Press and hold B button will go into the TIME SET mode with the AL HOUR blinking. Press A to set the AL HOUR. Press B to select digits in the following sequence: AL HR, AL MIN first digit, AL MIN 2nd digit, AL OFF/ON, YEAR last digit, YEAR 1st digit, MONTH, DATE, 12/24HR selection, HOUR, MIN 1st digit, MIN 2nd digit, and SECONDS.
Page 12
CARE OF YOUR STOPWATCH *WATER-RESISTANCE The stopwatch is designed to withstand accidental contact with water such as splashes or rain, but it is not designed for use in water. Do not operate the buttons when the stopwatch is wet. *TEMPERATURE Do not leave your stopwatch under direct sunlight or in very high temperatures for a long time, or the display may become black.
BATTERY CHANGE When the battery low indicator lights up, as shown in Fig.25, battery replacement is necessary. Fig.25. 1. Unscrew and remove the back cover. 2. Unscrew the battery contact. 3. Replace with fresh Lithium battery CR2032 or equivalent. 4. Before putting in the fresh battery make sure that the triangular contact is in the triangular slot under the battery.
SYSTEM PRINTER 499-P (Optional) Fig.26. BATTERY INSERTION 1. With the POWER SWITCH in the OFF position press and slide down the battery cover. 2. Put in 4 pcs of AA size batteries in polarities as shown in the battery compartment.
5. Keep pressing the PAPER ADVANCING SWITCH until the end of paper is 2-3 cm out from the printer. 6. Put the roll of paper into the paper compartment and close the paper cover. Fig.27. ** NEVER pull paper from the reverse direction, this may damage the printer. For replacing the roll of paper before it is used up, first tear off the paper and press the PAPER ADVANCING SWITCH until all the remaining paper is out.
Fig.28. OPERATION IMMEDIATE PRINT-OUT 1. Switch the stopwatch to ‘PRINT ALL’ mode as shown in Fig. 20. 2. Connecting the stopwatch to the printer, slide the power switch to ON, the paper will advance by 1 line. 3. Slide the PRINT MODE SWITCH to the TOP position. Only the SPLIT or SPEED (depending on whether the stopwatch is in CHRONO or SPEED mode) will be printed.
Page 17
Remarks: • Do not pull out the paper when the printer is not in operation. • Do not print if there is no paper in the printer. • Keep the printer from high moisture or dusty environment. • Do not subject the printer to violent shocks. •...
Need help?
Do you have a question about the 499 and is the answer not in the manual?
Questions and answers