FoxAlien Masuter Pro User Manual

FoxAlien Masuter Pro User Manual

Desktop cnc router
Hide thumbs Also See for Masuter Pro:

Advertisement

Desktop
CNC Router
M a s u t e r P r o
USER MANUAL
Please read this manual carefully before using.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Masuter Pro and is the answer not in the manual?

Questions and answers

Сергей
May 7, 2025

Помогите настроить.

Summary of Contents for FoxAlien Masuter Pro

  • Page 1 Desktop CNC Router M a s u t e r P r o USER MANUAL Please read this manual carefully before using.
  • Page 2: Table Of Contents

    Catalog Warranty & Disclaimer Product Specifications How to Assemble the Machine Wiring Diagrams • XYZ Stepper Wiring Diagrams • XYZ Limit Switch Wiring Diagrams • Spindle & Light Wiring Diagrams Controller Instructions How to Install the Router Bit How to Use Grblcontrol (Candle) •...
  • Page 3: Warranty & Disclaimer

    Warranty & Disclaimer Please be careful when using your CNC machine. This machine is an electrical device with moving parts and dangerous areas. • This CNC Machine is for Indoor Use Only. • Wear the proper protection equipment while operating. •...
  • Page 4: Product Specifications

    Product Specifications Model Masuter Pro 400 x 400 x 60mm (15.75” x 15.75” x 2.36”) Working Area Input Voltage Input Current Spindle Power Spindle Speed 10000 r/min Motor NEMA17 Firmware Version 1.1H Limit Switch X, Y, Z Emergency Stop Button...
  • Page 5: How To Assemble The Machine

    How to Assemble the Machine Y-axis Aluminum Profile (L) Y-axis Aluminum Profile (R) X-axis Aluminum Profile M5*20 Flat Cap Bolt...
  • Page 6 How to Assemble the Machine MDF Spoil Board M5*20 Bolt...
  • Page 7 How to Assemble the Machine X-axis Gantry M5*16 Flat Cap Bolt...
  • Page 8 How to Assemble the Machine Spindle Holder M5*12 Bolt Washer...
  • Page 9 How to Assemble the Machine Spindle...
  • Page 10 How to Assemble the Machine Y-axis Drag Chain Bracket Y-axis Drag Chain Bracket M3*6 Button Cap Bolt...
  • Page 11 How to Assemble the Machine X-axis Drag Chain Bracket M3*6 Button Cap Bolt...
  • Page 12 How to Assemble the Machine Controller Support Plate Controller M3*8 Button Cap Bolt -10-...
  • Page 13 How to Assemble the Machine M5*8 Bolt M5 T-nut -11-...
  • Page 14 How to Assemble the Machine Hex Wrench -12-...
  • Page 15 How to Assemble the Machine Y Axis Drag Chain M4*6 Flat Cap Bolt -13-...
  • Page 16 How to Assemble the Machine Y Axis Drag Chain M4*6 Flat Cap Bolt -14-...
  • Page 17: Wiring Diagrams

    Wiring Diagrams - X, Y & Z Stepper Motors Wiring Diagrams -15-...
  • Page 18: Xyz Limit Switch Wiring Diagrams

    - X, Y & Z Limit Switches Wiring Diagrams -16-...
  • Page 19: Spindle & Light Wiring Diagrams

    - Spindle & Light Wiring Diagrams Positive wire (Red) connects to the port with red dot Negative wire (Blue) connects to the other port Light: Insert the plug to the socket 60W spindle plugged into Spindle 1 socket Flip the toggle switch to the right side -17-...
  • Page 20: Controller Instructions

    Controller Instructions Toggle Switch: Flip to the left when using 300W Spindle Flip to the right when using 60W Spindle or Laser 300W Spindle Interface(Spindle2) 60W Spindle Interface(Spindle1) Toggle Switch Laser Interface Emergency Stop Button Power Button Home Button 24-48V DC Input USB Interface Offline Controller Interface Light On/Off...
  • Page 21: How To Install The Router Bit

    How to Install the Router Bit -19-...
  • Page 22: How To Use Grblcontrol (Candle)

    How to Use Grblcontrol (Candle) -Driver Installation Download from U disk. Click “INSTALL” Wait until it shows “Driver install success” Double-click to start installation. To Determine your Machine's COM port • For Windows XP: Right click "My Computer"→ Select "Manage"→ Select "Device Manager". •...
  • Page 23: Grblcontrol (Candle) Working Interface Introduction

    -Grblcontrol (Candle) Working Interface Introduction Coordinate display 3D preview interface, hold the Status display left mouse button, can rotate Common operation button, the mouse Angle, scroll the mouse icon on the above shows the specific wheel, can be enlarged, function or reduced.
  • Page 24: Make Your First Cut

    Make Your First Cut If Status becomes Alarm and [MSG: Check Limits] appears in the console at the same time, please check whether the limit switch is triggered. You can power off and release the limit switch Double click to start manually or refer to page Grblcontrol (Candle) 24 of the manual to release...
  • Page 25 The best distance between the bit and the object is that the bit should feel the A4 paper, and the paper can pass through the bit. 1. Open the file Fix the MDF with the clamps 2. Choose the Step and Feed (Unit: mm) 3.
  • Page 26: How To Unlock Limit Switch

    How to Unlock Limit Switch Command window will show: “ALARM:1 Limit switch will trigger when the Click “Reset” [MSG: Reset to continue]” machine runs out of active working area. If status change to “Alarm” again, that means it Click direction buttons to move the Click “Unlock”...
  • Page 27: How To Use E-Stop

    How to Use E-stop Press down E-stop when the machine Rotate clockwise to release the E-stop. Status in software will change to “Alarm”. malfunctions to avoid damage. Print “[MSG:’$H’|’$X’ to unlock]” Click “Unlock” to normal working status. -25-...
  • Page 28: Z-Probe Operating

    Operating Z-Probe Modify Z-probe parameter. Default value is Z15, change it to Z14.83 base of the parameter measured. Connect the wire Measure Z probe actual size (Thickness: 14.83mm) Click Z-probe button to start detecting. Click ”Zero XY” After Z-probe detection finished, remove Z-probe, click “Send”...
  • Page 29: Extended Accessories

    Extended Accessories (Available on foxalien.com) - Offline Controller - Laser Module Note: USB connection and offline controller can not be used at the same time. Please unplug the USB cable when using the offline controller, otherwise it may cause errors, deviation or unusual stopping during engraving.
  • Page 30: 300W Spindle

    Extended Accessories (Available on foxalien.com) - 300W Spindle Flip the toggle switch to the left 300W spindle plugged into Spindle 2 socket 300W Spindle Installation and Wiring Diagrams -28-...
  • Page 31 Please visit www.foxalien.com for more CNC machine accessories products. Feel free to contact us for technical support if you come across any difficulty during assembly and using. E-mail: aftersale@foxalien.com, support@foxalien.com We will response within 1 business day. Files Download Facebook Group Foxalien.com...

Table of Contents

Save PDF