Table of Contents
Related Manuals for ALVEO3D ALVEOPRO - M100
Summary of Contents for ALVEO3D ALVEOPRO - M100
- Page 1 INSTRUCTIONS MANUAL ALVEO3D ALVEOPRO - M100 Filtering system for 3D printer - HEPA14 & active carbon Find all assembly resources www.alveo3d.com/en/assembly-alveopro/ and download contents www.alveo3d.com/en/download-alveopro/ v1.0 EN...
-
Page 2: Table Of Contents
TABLE OF CONTENTS p. 1 TABLE OF CONTENTS p. 2 SAFETY PROVIDED ELEMENTS p. 3 ALVEOPRO - M100 p. 4 p. 5 STEP 1 - POSITION FILTER STEP 2 - ASSEMBLY TOP COVER p. 6 STEP 3 - MOUNT EXTENSIBLE HOSE p. -
Page 3: Safety
SAFETY Read all instructions before using 3D printer enclosures contain harmful emissions from 3D printing. It is advised to always turn the filtering system on during the printing process. The filtering system is powered by a high-pressure fan. Do not turn on the fan before full assembly is done with the protective grid and the P3D filter. -
Page 4: Provided Elements
PROVIDED ELEMENTS Provided elements with ALVEOPRO - M100 ALVEOPRO - M100 assembled 4 x knurled screw Top cover adaptator - 2 elements Extensible hose 3 meters Enclosure connector - 2 elements Power supply 24v EU plug Filter M100 with a sealable plastic bag USB cable Allen key 2.5mm... -
Page 5: Alveopro - M100
ALVEOPRO - M100 Extensible hose Enclosure connector Cone Enclosure connector Clamp ring Top cover connector Top cover connector Clamp ring Filter M100 AlveoPRO Rotary encoder... -
Page 6: Step 1 - Position Filter
STEP 1 . POSITION FILTER Take the filter out of the sealable plastic bag, remove the protective transparent film. Use the handles to position the filter between the guides. HEPA surface (white surface) still remain visible. Use handles to take the filter out of the alveoPRO case. -
Page 7: Step 2 - Assembly Top Cover
STEP 2 . ASSEMBLY TOP COVER Put the hexagonal nuts in their slots on the clamp ring. Then assemble on both sides of the top cover the clamp ring and the top cover connector with the black countersunk M3 screw 10 mm. Black countersunk M3 screw 10 mm Top cover connector... -
Page 8: Step 3 - Mount Extensible Hose
STEP 3 . MOUNT EXTENSIBLE HOSE Extend one end of the hose then plug it into the top cover connector by rotating the hose in the threading. extended hose Threading to screw the hose The hose goes inside the top cover connector... -
Page 9: Step4 . Connect To Enclosure
STEP4 . CONNECT TO ENCLOSURE Extend the other one end of the hose by 10 cm. Use the countersunk M4 screw 16 mm for panel thickness from 2 to 7 mm. Use the countersunk M4 screw 20 mm for panel thickness from 8 to 12 mm. Place the clamp ring on the extended hose. -
Page 10: Step 5 - Connectivity & Start
STEP 5 . CONNECTIVITY & START plug the power supply on the backside of the device, then press the ON/OFF switch to turn it ON or OFF. The USB connector will be used to update the device firmware and remote control function. Switch ON/OFF Connector... -
Page 11: Step 6 - Display Interface
- FILTER : Settings and information regarding the filter - INFOS : General information and technical support Firmware version number Rotary encoder ALVEOPRO - M100 ALVEOPRO - M100 LOADING ... LOADING ... VS 1 .0 .0 VS 1 .0 .0... -
Page 12: Step 7 - Fan Control
STEP 7 . FAN CONTROL In the menu START, fan speed can be manageg as well as the timer. With the timer, you can set the end of the countdown at the right time. ALVEOPRO ALVEOPRO PLAY STOP TIMER MENU PLAY starts filtration STOP stops filtration 00: 00: 00... -
Page 13: Step 8 - Timer Settings
STEP 8 . TIMER SETTINGS TIMER settings (countdown) manage the filtering time and let you set it to follow the printing time and hotbed cooldown. Select the TIMER icon then validate by pressing the rotary encoder. ALVEOPRO ALVEOPRO ALVEOPRO ALVEOPRO FAN TIMER PLAY STOP... -
Page 14: Step 9 - Filter Change
STEP 9 . FILTER CHANGE Filter M100 replacement comes with a new initialization process through the display interface: Follow the steps below : ALVEOPRO In the main menu select « FILTER» then get access to filter management option. START SETTINGS FILTER INFOS 00:00... -
Page 15: Step 10 - Online Support
3D files will be shared as well. AlveoPRO firmware will be seasonally updated to bring new functionalities. To install incoming updates, go to www.alveo3d.com with the link below : https://www.alveo3d.com/en/alveopro-support/ The enclosure connector is available in STEP format on the support page (link above) in order to let you modify it easily to fit with your enclosure shape. -
Page 16: Step 11 - Alert & Error List
SDP not responding Reboot the device #104 ERROR Tachymeter not responding FIRMWARE 1.0.0 Fan working but the screen displays 0 RPM Contact the Alveo3D technic support #105 ERROR FIRMWARE 1.0.0 Low pressure (small airdrop) Check if the filter is well positioned #106... -
Page 17: Notes
NOTES HEPA Filter P3D lifetime: Filter working life is associated with many factors including filament type, melting temperature, the concentration of nanoparticles and VOCs, ambient humidity... We suggest replacing HEPA filter P3D according to the following table: Intensive use Occasional use Filter replacement 6 months 12 months... - Page 18 NOTES :...
- Page 19 NOTES :...
- Page 20 Breath ! You are filtering ! Share your experience on www.facebook.com/alveo3d/ ALVEO3D by FLEXEE SYSTEM SAS 386 Rue de la Curiaz 73290 La Motte-Servolex www.alveo3d.com contact@alveo3d.com Designed & assembled in France...
Need help?
Do you have a question about the ALVEOPRO - M100 and is the answer not in the manual?
Questions and answers