Advertisement
Quick Links
IG 1300 Series
When installing outdoors, care must be taken to comply with all local and national elec-
tric codes regarding outdoor or wet locations. Do not touch electric devices when you
are wet or you are standing on a wet surface. Use a circuit tester or AC voltmeter to be
sure the electricity is "OFF' before you touch wires or devices.
Install Telephone protection per Article 800 of the National Electrical Code on the equip-
ment side of the primary telephone Listed equipment.
ELECTRICAL GROUND IS REQUIRED FOR THIS UNIT TO
STEP 1
Verify that all parts are included for your system.
DESCRIPTION
PanelGuard IG1300 AC Voltage Protection Device
with 30" wire leads
Mounting Plate
Wire channel cover
4-wire (2-pair) Telephone protection module
1-circuit coaxial cable protection module
STEP 2
Tools and additional materials required.
AC Voltmeter or Voltage tester
Screwdrivers
Flat or phillips blade for cabinet mounting screws.
Torx T-20 for internal screws
Lineman's pliers or wire strippers
Hammer (optional)
3 each 1-1/4" x #10 sheet metal, wood or masonry screws
NOTE:
FUNCTION PROPERLY AND SAFELY!
I
NSTALLATION
I
NSTRUCTIONS
CAUTION !
Electricity is dangerous if safety rules
are not followed. Never work on equip-
ment with the electricity turned 'ON'. Be
absolutely certain the power is turned
'OFF' on the circuit or device you are
installing or repairing. If you are not
able to determine that power is removed
have it checked by a licensed electri-
cian. Be sure you read carefully and
understand all of these installation steps
and have the necessary tools and sup-
plies before you begin to install the pro-
tector. Check and follow your local elec-
trical codes, they are for your protection.
QUANTITY
(IG1300-2T-1C)
1
1
1
1
1
QUANTITY
(IG1300-4T-2C)
1
1
1
2
2
Advertisement
Related Manuals for Intermatic IG1300
Summary of Contents for Intermatic IG1300
- Page 1 ELECTRICAL GROUND IS REQUIRED FOR THIS UNIT TO STEP 1 Verify that all parts are included for your system. DESCRIPTION PanelGuard IG1300 AC Voltage Protection Device with 30” wire leads Mounting Plate Wire channel cover 4-wire (2-pair) Telephone protection module...
- Page 2 Select a mounting position for the protector at the electric panel. If you have a panel that is not similar to the diagram in Figure 2, call Intermatic for assis- tance at the numbers listed at the end of these instructions between the hours of 8:00 am and 4:00 pm central time Monday through Friday.
- Page 3 STEP 11 The IG1300 Series is shipped ready for installation on the right-hand side or top positions of the electrical panel. If the protection panel is mounted on...
- Page 4 Confirm that the protector is wired to the correct breakers by measuring the voltage between the two black leads. A voltage of 220 to 240 VAC means that the IG1300 is connected across both sides of the electrical service. STEP 18 Replace the cover or trim panel on the electrical cabinet.
-
Page 5: Special Instructions
STEP 19 Close the cover on the IG1300. SPECIAL INSTRUCTIONS Use the following steps when installation requires placing the IG1300 on the left side of the electrical panel. STEP A Loosen the screw in hole C that secures the coaxial cable protection module(s) to the wire channel cover. - Page 6 Intermatic's option, either repair the Damaged Equipment or reimburse the purchaser of the defec- tive product. The limit of Intermatic's liability under this warranty shall be the Fair Market Value (as hereinafter defined) of the Damaged Equipment or the deductible amount of the original purchas- er's homeowner's insurance policy, whichever is less.
- Page 7 (2) What Is Not Covered By This Warranty Intermatic does not warrant (a) defects in the Product or damage to any equipment caused by the failure to properly install the Product, (b) damage caused by use of the Product for purposes other...
- Page 8 (C) File a claim for the damaged equipment with your homeowner’s (or renter”s) insur- ance company. (D) Send the INTERMATIC ® IG1300 Series Surge Protection Device to the at the address listed below. All returned devices must be plainly WARRANTY COORDINATOR...