Low Battery indicator End Call feature Last number redial Flash, Pause, Mute Programmable one-touch Call Forwarding on/off* Programmable one-touch Voice Message retrieve button* Tone/Pulse Dialing Hold Call Timer Headset Button Headset jack * function requires subscription to telephone company service...
9. Avoid using the telephone during an electrical storm. There can be a slight risk of electrical shock from lightning. 10. Do not use the telephone to report a gas leak, if in the vicinity of the leak. 11. Unplug this telephone from the wall outlet and refer servicing to qualified service personnel under the following conditions: • If liquid is spilled into the unit.
“Call Identification (Caller ID) Service” and/or “Call Waiting Caller ID Service” that is provided by your local telephone company. There is a fee for these services by your local telephone company, and they may not be available in all areas. When used with these services, your telephone displays the telephone number or the telephone number and name of each caller before you answer the call allowing you to screen your calls.
3. Pull out the mounting stand to the wall mounting position shown In figure 5. 4. To install as a wall unit. a. Align the holes on the back of the telephone mounting plate with the heads of the self tapping screws.
MEMORY 2 button MEMORY 3 button REDIAL button SPEAKER button Volume (+ and -) buttons MEMORY SPEED DIAL buttons (10x) SHIFT button Data jack Ringer volume switch Telephone jack 9VDC power jack Headset jack Handset jack Dialing mode switch Bottom of Phone...
Message Waiting Lamp If you subscribe to “Voice Messaging” (a service offered by your telephone company) this lamp will flash whenever a new message is on the system. This light should stop flashing after the call is retrieved. LCD Contrast Function The contrast on your LCD screen is adjustable.
Page 10
LCD will display “MUTE” while the function is active. FLASH Button If you subscribe to “Call Waiting” (a special telephone service) the FLASH button is used to connect the line to another incoming call or to establish a dial tone to make another call while still connected to the initial caller.
Page 11
The network service buttons are memory keys programmed to dial as shown below: Stop Call Waiting Messages Access codes for network services are not the same for all telephone companies. See “Re-Programming Network Service Buttons” below to store a different access code. • Message Function If you subscribe to “Voice Messaging”...
Page 12
After you hand up, Call Waiting will be reactivated for you next call. • Re-Programming Network Service Buttons Access codes for network services are not the same for all telephone companies. To store a different access number or to restore the access number to the appropriate button, do the following: 1.
To access the function settings of this phone, press the MENU button and use the buttons to select a function. NOTE: The phone must be in the on-hook position to access the MENU mode settings. The setting sequence is PHONE BOOK - CALL WAITING - DATE FORMAT - HOUR FORMAT - SET FLASH - SET AREA CODE - SET LANGUAGE - SET TIME - LCD CONTRAST - BACK LIGHT.
Page 14
Function Operations 2. With the phone on-hook, you may directly access the phonebook by pressing the number 1 plus #. The LCD will show the first name/number entry in the phone book. Use the or button to scroll to the desired name/number. The contact displayed in the LCD can be automatically dialed by picking up the handset.
Page 15
TIME SETTING If you have subscribed to Caller ID, the date and time will be automatically set when the first call is received. To set the time manually follow the instructions below: Press the MENU button, using the or scroll to SET TIME - press ENTER, then using the keypad, enter the correct time, date and day of week.
1. When you are on the line, the telephone will display the name and number of the second caller. 2. Press the FLASH button to answer the second caller.
A caller ID record consists of the following information: Reviewing Display Messages MESSAGE WAITING - If you have voice mail service from your telephone company and a message is left, the MESSAGE WAITING light will turn on and the message icon will appear in the upper left corner of the LCD.
Caller ID System Operations Subscription to Caller ID service and/or voice mail service from your local phone company is required to experience these features. • New Voice Message Indicator - The red indicator light above the LCD will flash to indicate that you have a new voice message waiting. The lamp will continue to flash until all the new calls have been reviewed.
• Check ringer switch on the back of the phone. If ringer is on, you may have too many communication devices hooked to a single line. A communication device can be a phone, modem or facsimile (FAX) machine. Contact your telephone company for help in calculating the limit for your residence or business line. NO DIAL TONE • Verify that the line cord is plugged in correctly.