Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Velcom Manuals
  4. Greenhouse Kit
  5. MAGNOLIA
  6. Manual

Velcom MAGNOLIA Manual

Made of 1" x1" (25x25mm) steel galvanized profile tube
Hide thumbs Also See for MAGNOLIA:

Advertisement

Quick Links

Download this manual
GREENHOUSE
" MAGNOLIA "
Made of 1" x1" (25x25mm) steel galvanized profile tube

Advertisement

loading

Related Manuals for Velcom MAGNOLIA

Summary of Contents for Velcom MAGNOLIA

  • Page 1 GREENHOUSE “ MAGNOLIA ” Made of 1" x1" (25x25mm) steel galvanized profile tube...
  • Page 2 - 2 -...
  • Page 3 Width 10'(3m) Height 7'(2,1m) Base length 13'(4m) • Extension on 6.5'(2m) - 3 -...
  • Page 4 COMPLETE SET OF “MAGNOLIA” PRODUCT Fig. 1 End-face Fig. 2 Intermediate arch Fig. 3 Framework assembling (side view) Fig. 4 Door and air gate LIST OF CONSTITUENT PARTS FOR ASSEMBLING Q-ty Q-ty Part Name Picture BASE EXTEN/ End-face half-arch, left-hand,...
  • Page 5 The left-hand part of the bottom transverse rib of end-face, 1050mm Middle part of the bottom transverse rib of the end-face, 900mm The right-hand part of the bottom transverse rib of end-face, 1050mm Grouser post, 20х20х250mm U-shaped grouser, 150mm Intermediate arch half-arc, left-hand 1605mm Intermediate arch half-arc, right-hand, 1605mm...

  • Page 6: Product Description

    Door stop plate, 100mm 1. PRODUCT DESCRIPTION Greenhouse “MAGNOLIA” is designed to create an optimal microclimate for growing vegetables, flowers and seedlings in the smallholding. The framework parts are made of steel galvanized profile tube with a square cross-section of 25 x 25 mm The greenhouse is intended to be covered with cellular polycarbonate.
  • Page 7 2. END-FACES ASSEMBLY 2.1. Connect the left half-arc #1 and right half-arc #2 of the end-face (the half- arcs of the first end-face are marked by "1A" and "2A”; the half-arcs of the second end- face are marked by "1B" and "2B"). Secure the connection with self-tapping screws #37 (2 on each side).
  • Page 8 2.4. Secure the left-hand #10 and right-hand #11 parts of the bottom transverse rib to the extensions #10 with self-tapping screws #37: 2.5. Connect the middle part #11 of the bottom transverse rib to the left and right parts, and simultaneously attach the left #4 and right #5 doorway posts to them. Secure the connections with self-tapping screws #37: 2.6.
  • Page 9 2.7. With self-tapping screws #37 attach jib-sticks #9 to the posts ##4-5 and the bottom lintel ##10-12, setting the angle of 90° with a try square: 2.7. Use self-tapping screws #37 to attach the jib-sticks #8 to the side posts #7t and the roof end arch: 2.8.
  • Page 10 2.9. Secure stop plate #43 with self-tapping screws # 37 in the corner of the door way on the inside: 2.10. Using parts ##18-22 and self-tapping screws #37, assemble the doors. Use a try square to ensure correct geometry when assembling. The door post #22 with hinge holes should be on the right-hand side: - 10 -...
  • Page 11 2.10. Using parts ##23-25, jib-sticks #9 and self-tapping screws #37, assemble the air gates. Use a try square to ensure correct geometry when assembling. The air gate post #27 with hinge holes should be on the right-hand side: 2.11. Insert the air gate in the door, secure with two hinges #42 using screws #35 and nuts #36.
  • Page 12 3. INTERMEDIATE ARCHES ASSEMBLING 3.1. Similarly as in cl. 2.1, connect the left half-arc #15 and right half-arc #16 of the intermediate arch . Secure the connection with four self-tapping screws #37 (two on each side). 3.2. Using the assembled end-face as a template, place the assembled arch and posts #7 on it (one of the Ø7mm holes in the posts should be at the bottom).
  • Page 13 4. FRAMEWORK ASSEMBLING 4.1. Connect the assembled end and six starting stringers #27 by bolts #32 with washers #33 and nuts #34 through the holes drilled in the end-face. 4.2. Fasten the two assembled intermediate arches to the starting stringers by bolts #32.
  • Page 14 4.8. Install the angle pieces # 29 (120 °, 2025 mm) at the joints of posts and roof arcs, fix them with self-tapping screws #37. 5. GROUSERS ASSEMBLING 5.1. Using self-tapping screws #37 connect grouser #14 to the grouser post #13 so that you get a T-shaped leg.
  • Page 15 6 CUTTING OUT AND INSTALLATION OF CELLULAR POLYCARBONATE (CP) TO THE END-FACES Warning! When installing the CP, it is important that the CP cellular lines are vertical (from top to bottom). Be sure to remove the wrapping film from both sides of the sheet.
  • Page 16 Layout of polycarbonate sheets on the end-face Scheme of polycarbonate fastening on the end-faces, There are 48 self-tapping screws and thermal washers per one end-face Using self-tapping screws #37 6.7. secure the door holder # 41 to the right middle end-face lintel and fix the mating hinge of the door so that the door holder secures the door in the open position.
  • Page 17 7. Mounting of Cellular polycarbonate (CP) on the roof Warning! When installing the CP, it is important that the CP cellular lines be on the roof along the arcs, and on the side walls - vertically. The parts "D" with the size of 2100x3250mm are used for mounting. 7.1.
  • Page 18 8. MOUNTING OF CELLULAR POLYCARBONATE (CP) ON THE SIDE WALLS The parts "E" with the size of 2100x1650mm are used for mounting. 8.1. Start mounting the CP sheets to the sides from the end-faces. Place the CP sheet to the side of the framework, aligning the top of the CP to the center of angle piece #29 and the side edge of the CP to the end post.
  • Page 19 9. INSTALLATION OF EXTERIOR ANGLE PIECES 9.1. Using #38 self-tapping screws mount four angle pieces #30 (90°, 1600 mm) on the vertical corners of the framework, 8 self-tapping screws per angle piece, thus closing the vertical corner joints of polycarbonate: 9.2.
  • Page 20 10. Greenhouse installation 10.1. Before starting operations, the site on which the greenhouse will be installed should be carefully leveled. 10.2. Dig holes or trenches of sufficient length and width under the legs equipped with grousers. 10.3. Position the assembled greenhouse so that the bottom longitudinal stringers are on the same level with the ground and the legs are deepened into the ground.
  • Page 21 Warrantee obligations The manufacturer guarantees that the greenhouse framework (hereinafter referred to as the product) is new, fully equipped, and free of manufacturing defects. The manufacturer is responsible for the completeness of the product. The manufacturer is responsible for the assembly of the product according to the instructions.
  • Page 22 We are grateful for your choosing the “Magnolia” greenhouse which will serve you for decades under proper usage! Due to the continuous improvement of “Magnolia” products the manufacturer reserves the right to make changes in the design without prior notice to the consumer.
  • Page 23 - 23 -...
  • Page 24 Quantity of sheets and cutting scheme of cellular polycarbonate with the size of 2100x6000mm for greenhouses M agnolia with length of 4 - 6 - 8 - 10 m Magnolia greenhouse with length of 4m (1 base) Cellular polycarbonate sheet 2100х6000 mm – 3 pcs.
  • Page 25 Magnolia greenhouse with length 6m (1 base + 1 extension) Cellular polycarbonate sheet 2100х6000 mm – 5 pcs. - 25 -...
  • Page 26 Magnolia greenhouse with length of 8m (1 base + 2 extensions) Cellular polycarbonate sheet 2100х6000 mm – 6 pcs. Cellular polycarbonate sheet 2100х2000 mm – 1 pc. - 26 -...
  • Page 27 NOVA greenhouse with length of 10m (1 base + 3 extensions) Cellular polycarbonate sheet 2100х6000 mm – 7 pcs. Cellular polycarbonate sheet 2100х4000 mm – 1 pc. - 27 -...