Related Manuals for Velcom CAMELLIA R
Summary of Contents for Velcom CAMELLIA R
- Page 1 TECHNICAL MANUAL CAMELLIA R Made from 1” x 1” galvanized steel pipe Set of product Width 10ft • Height 7ft Length of 19.5ft • Extension 6.5ft etc.
- Page 2 PRODUCT COMPLETE SET PARTS uuuuProduct Q-ty Q-ty Part name Denotation BASE EXTEN. End face half-arc, left-hand, 2535mm End face half-arc, right-hand, 2355mm End face lintel, top, 960mm Door way post, left-hand, 2020mm Door way post, right-hand, 2020mm End face transverse member, left- hand, middle, 990mm End face transverse member, right- hand, middle, 990mm...
- Page 3 The left-hand part of the end face bottom-end transverse member, 1050mm Middle part of the end face bottom- end transverse member, 900mm The right-hand part of the end face bottom-end transverse member, 1050mm Intermediary arch half-arc, left-hand , 2535mm Intermediary arch half-arc, right-hand , 2355mm Transverse enhancer of the intermediate arch, 1500mm...
-
Page 4: Product Description
Door stop plate, 100mm 1. PRODUCT DESCRIPTION Greenhouse CAMELLIA R is designed to create an optimal microclimate for growing vegetables, flowers and seedlings in the smallholding. The frame parts are made of steel galvanized pipe with a square cross-section of 25 x 25 mm. - Page 5 2. END FACES ASSEMBLY 2.1. Joint the left-hand end face half-arc No.1 and the right-hand end face half-arc No. 2 (half-arcs of first end face are marked with "1A" and "2A"; half-arcs of the second end face are marked with "1B" and "2B"). Fasten the connection with self-tapping screws No.
- Page 6 2.4. Fasten the left-hand No.11 and right-hand No.13 parts of the bottom-end transverse part to the No.10 extensions with No.41 self-tapping screws: 2.5. Connect the middle part No.12 of the bottom-end transverse part to the left- hand and right-hand parts, with simultaneous attachment of the left-hand No.4 and right-hand No.5 doorway posts to them.
- Page 7 2.7. Install the left-hand No.6 and the right-hand No.7 end face transverse parts and fasten them with self-tapping screws No.41: 2.8. Install the left-hand No.8 and the right-hand No.9 end face diagonals and fasten them with self-tapping screws No.41: 2.13. Fasten stop plate No.46 with self-tapping screws No.41 to the corner of doorway on the inside: - 7 -...
- Page 8 2.9. Using parts Nos.18-23 and self-tapping screws No.41 assemble the doors. Use an angle piece to ensure correct geometry when assembling. The doorpost No.23 with hinge holes should be on the right-hand side: 2.10. Using parts Nos. 24-28 and self-tapping screws No.41 assemble the air gates.
- Page 9 2.11. Insert the air gate in the door and secure it with two hinges No.45 using screws No.39 and nuts No.40. Fasten the upper hinge of the door to the upper hinge of the air gate, and fasten the lower hinge of the door to the lower hinge of the air gate: 2.12.
-
Page 10: Frame Assembly
4. FRAME ASSEMBLY End face “A” Intermediate arch End face “B” 4.1. Fasten starter stringers No.32 to the “A" end face of the inside of the arch with bolts, washers and nuts Nos.36-38 inserted into the drilled holes. 4.2. Fasten two intermediate arches to the starter stringers using bolts, washers and nuts Nos.36-38. - Page 11 6. FASTENING OF MULTIWALL POLYCARBONATE (PC) TO THE END FACES 6.1. Place a 2100 mm x 6000 mm PC sheet face up on a flat surface. 6.2 Cut the sheet lengthwise into two equal pieces of 1050 mm x 6000 mm. Cut the sheets into pieces according to the diagram: мм=mm 6.3.
- Page 12 Scheme of polycarbonate fastening on the end faces. 6.6. Fasten the peg stay No. 44 on the right-hand middle lintel of the end face with self-tapping screws No. 41, and the mating hinge on the door so that the peg stay fixes the door in the open position.
- Page 13 7. FASTENING OF MULTIWALL POLYCARBONATE (PC) TO THE ROOF WARNING! Before installation of PC on the roof make sure that the geometry of the frame is correct. The diagonal distance between the corners of the frame should be equal. The longitudinal stringers must be plane, without bends and distortions. It is necessary to remove the wrapping film from both sides of the sheet.
- Page 14 7.7. Mount with overlapping joint the intermediate PC sheet to the previous sheet and tighten with the tie bands. After installing all the sheets, check the correct positioning of the PC sheets, the parallel alignment of PC lines to the arches, the position and the tension of the tie bands.
- Page 15 WARRANTEE OBLIGATIONS The manufacturer guarantees that the greenhouse frame (hereinafter referred to as the product) is new, fully equipped, and free from manufacturing defects. The manufacturer is responsible for the completeness of the product. The manufacturer is responsible for the assembly of the product according to the instructions.
- Page 16 Thank you for choosing the CAMELLIA R greenhouse which will serve you for decades under proper usage! Due to the continuous improvement of the products the manufacturer reserves the right to make changes in the design without prior notice to the consumer.