Advertisement
Quick Links
TECHNICAL MANUAL
CAMELLIA
Made of 1"x1" Galvanized Steel Pipe
Covered with High Density UV Polycarbonate
Set of product
Width 10ft (3m) • Height 7ft (2.10m)
Length of base 13ft (4m) • Optional Extension by 6.5ft (2m) etc.
Thank you for cho os ing the M AG N OLIA greenhous e
Advertisement
Related Manuals for Velcom CAMELLIA
Summary of Contents for Velcom CAMELLIA
- Page 1 TECHNICAL MANUAL CAMELLIA Made of 1”x1” Galvanized Steel Pipe Covered with High Density UV Polycarbonate Set of product Width 10ft (3m) • Height 7ft (2.10m) Length of base 13ft (4m) • Optional Extension by 6.5ft (2m) etc. Thank you for cho os ing the M AG N OLIA greenhous e...
- Page 2 TECHNICAL CERTIFICATE of GREENHOUSE “CAMELLIA” DISCRIPTION The greenhouse “CAMELLIA” is designed to create the climate, which is productive to grow horticultural crops on the garden plots. The length of the greenhouse is 13’L (4m) width is 10’ (3m) and height is 7’ (2.10m) with ability to extend length by 6.5’...
-
Page 3: List Of Accessories
1. LIST OF ACCESSORIES Insert Figure Base +6.5’L Part name (can vary from the actual 13’L (2m) (4m) configuration) optional Part of the end arch “A” left Part of the end arch “A” central (with X-inserts) Part of the end arch “A” right Part of the end arch “B”... - Page 4 central (with X-inserts) Part of intermediate arch “E”, right Lug stand, 250 mm Lug crossbar, 150 mm Connective stringer, launching, 2012 mm Connective stringer with Х- pressing, 2068 mm End brace, 600 mm Fixing strap , 20x6150 mm Bolt М6х60 mm Nut М6 Washer М6 Screw М4х35 mm...
- Page 5 2. ASSEMBLY DIAGRAM “CAMELLIA” PRODUCT Fig.1 Ends “A”, “B” Fig.2 Intermediate arch “E” Fig.3 Frame assembly (side view) Fig.4 Doors “C”, “D” 3. ASSEMBLY OF ENDS “A” and “B” (identically the same). Attention! Places of fastening parts are indented and circled with a marker.
- Page 6 3.1. Connect left No.1A, central No.2A and right No.3A parts of the end arch “A”. Fasten the joint with self-tapping screws No. 46 on both sides (4 self-tapping screws per one joint). In a similar fashion, assembly the end arch “B” using parts Nos. 1B/2B/3B: 3.1.
- Page 7 3.4. Install upper crosspiece between posts Nos. 7-8 at 1950 mm from the lower crosspiece fasten with self-tapping screws No. 46: 3.5. Install four lateral crosspieces between jamb posts Nos. 7-8 and side posts No. 3 at 900 mm from the lower crosspiece and fasten with self-tapping screws No.
- Page 8 3.8. Use parts Nos. 15-16-17-18-19 to assemble the upper door “C” and lower door “D” with the help of self-tapping screws No. 46. Door posts No. 16 with apertures for door hinges must be to the right, and posts Nos. 17(18) with the aperture for the door handle must be to the left. The upper door “C”...
- Page 9 4. ASSEMBLY OF INTERMEDIATE ARCS “E” 4.1. Connect parts of arches Nos. 21-22-23 with self-tapping screws No. 46, 2 self-tapping screws No. per one joint at 60 mm from the pipe end: 4.2. Use self-tapping screws No. 46 to fasten crosspiece No.
- Page 10 5.2. Fasten two intermediate arches “E” to launching stringers using bolts No. 40. 5.3. Insert Х-pressing stringers No. 27 into launching stringers No. 26. 5.4. Fasten intermediate arches “E” to stringers No. 27 with bolts No. 40 through the drilled holes. 5.5.
- Page 11 The End Face “A” and End Face “B” are identically the same! Quantity of Polycarbonate sheets for different size of Arch Greenhouse CAMELLIA 13’L x 10’W x 7’H (1 Base) – For the Ends 1 sheet For the Roof 2 sheets 19.5’L x 10’W x 7’H (1 Base, 1 Insert) –...
- Page 12 6. POSITIONING OF CELLULAR POLYCARBONATE ON THE ENDS “A”,”B” Important! For Polycarbonate positioning it is important that all cellular lines be located in a vertical position (downwards). Be sure to remove the wrapping film from both sides of the sheet. The manufacturer marks the work face (sunward) of cellular polycarbonate with a certain mark (a color bar, sticker or other).
- Page 13 6.4. Hold part 3 of Polycarbonate against the left part of the end, and part 4 of Polycarbonate against the right part of the end; align the Polycarbonate lower edge against the lower crosspiece of the end. Fasten parts 3 and 4 with self-tapping screws No. 46 via thermo- washers No.
- Page 14 6.6. Fasten the door holder No. 49 to the right crosspiece of the end with self-tapping screws No. 46, and fasten the hinge of the door holder on the lower door lintel for the holder to fix the door in the open position (see the figure above).
- Page 15 7.1. First, position margin Polycarbonate sheets (from the ends). Position Polycarbonate sheets so that they overlap (overhang) the end edge by 50 7.2. Press down the first Polycarbonate sheet with fixing strap No. 31 (position 1) and fasten one end of the strap to the arch foot beneath the polycarbonate edge with self-tapping screw No.
- Page 16 7.7. Position the intermediate Polycarbonate sheet with overlap to the neighboring sheet and press it down with the fixing straps. After all sheets are positioned, check whether Polycarbonate sheets position is correct and whether cellular lines are parallel to the arch bows. Check the position and tensioning of fixing straps. Check the fixing strap tensioning at least once a year.
- Page 17 ATTENTION! The greenhouse has a surface exposed to the wind. Do not leave the greenhouse unfixed. When the greenhouse is installed in a windy area, use any additional available materials (rods, bars, etc.) for attachment to the ground. Do not install the greenhouse in close proximity (less than 2 meters) to any buildings, barriers, fences.
- Page 18 9. LIMITED WARRANTY OBLIGATIONS 1. The manufacturer guarantees that the greenhouse frame (hereinafter referred to as the product) is new, fully equipped, and free from manufacturing defects. 2. The manufacturer is responsible for completing the product. 3. The manufacturer is responsible for the collection of the product in accordance with the instructions.
- Page 19 Thank you for choosing the CAMELLIA greenhouse Which will serve you for decades under proper usage! Due to the continuous improvement of the products the manufacturer reserves the right to make changes in the design without prior notice to the consumer.