Advertisement
Quick Links
ASSEMBLY INSTRUCTION
2 seat outdoor swing
ITEM CODE: CS62671
For any assistance with assembly or for missing parts please Contact with us
Email: patiopostservice@lhgst.com
Web: www.lhgst.com
Adress:NO.99 South Heyang Road,Dayang Street, Linhai,zhejiang,China
Page 1
Advertisement
Related Manuals for Patio Post CS62671
Summary of Contents for Patio Post CS62671
- Page 1 ASSEMBLY INSTRUCTION 2 seat outdoor swing ITEM CODE: CS62671 For any assistance with assembly or for missing parts please Contact with us Email: patiopostservice@lhgst.com Web: www.lhgst.com Adress:NO.99 South Heyang Road,Dayang Street, Linhai,zhejiang,China Page 1...
-
Page 2: Pre-Assembly Preparation
PRE-ASSEMBLY PREPARATION Before you start: 1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product 2.Take care when lifting. Product should be assembled as near as possible to the point of use 3.Ensure that you have all required contents for complete assembly 4.Always read the assembly instructions carefully before beginning assembly. -
Page 3: Parts List
PARTS LIST Page 3... - Page 4 Step 1 You will need the following • Prepare a surface with a blanket or cardboard. • Prepare 8x bolt Q sets. Thread bolt(Q) through washer(U). • Connect part(C) and part(D) to part(A) and part(B) as shown below. • Secure with 2x bolt Q sets at each connection, fasten with Allen Key(AA).
- Page 5 Step 2 You will need the following • Attach the 2x swing arms(E) to the frame. The short end of the late, closest to the rode connects to the feet(A&B). The long end of the plate faces down. • Secure with bolt(S), threaded from the outside, through swing arm(E).
- Page 6 Step 3 You will need the following • Attach right armrest(F) to the swing arms(E) as shown below. • Thread bolt(S) from the outside through the armrest(F). Place the plastic washer(N) between the armrest and the swing arm. Lock the inside with washer(U) and nut(V). Fasten with Allen key(AA) and Wrench(BB), as shown below.
- Page 7 Step 4 You will need the following • With the aid of a 2 person, attach the base and back plate(H) to the armrests. • Thread bolt(S) from the outside of the middle bar of the armrest, in through armrest and part(H). Lock the inside with washer(U) and nut(V).
- Page 8 Step 5 You will need the following • Connect the top of the armrest to part(H). • Prepare 2x bolt R set, thread bolt(R) through washer(H) • Thread bolt R set from the inside of part(H) outwards. Place plastic washer(N) between the armrest and part(H). Fasten with Allen key(AA).
- Page 9 Step 6 You will need the following • Stand left and right tea table support(J&K) on the floor, attach the tea table connecting part(M) to the supports, as shown below. • Prepare 2x bolt R sets by threading bolt(R) through washer(U). •...
- Page 10 Step 7 You will need the following • Place the tea table panel(L) upside down on the prepared surface. • Place the completed table base on to part(L), as shown below. • Prepare 4x bolt R sets by threading bolt(R) through washer(U). •...
- Page 11 Step 8 You will need the following • Place the completed table frame on the base and back plate(H),as shown below. • Prepare 2x bolt R sets by threading bolt(R) through washer(U) • Secure the table to the chair with a bolt R set on either side of the table, as shown below.
- Page 12 Step 9 You will need the following • Secure the bottom of the table to part(H) • Insert bolt(T) down through the table as shown below. Insert plastic washer(P) in-between the table and the seat. Concave side up, flat side down. Lock the other side the bolt with washer(U) and nut(V), as shown below.
- Page 13 Assembly is complete Page 13...
- Page 14 Page 14...