MEGAlink ML2000 User Manual
Hide thumbs Also See for ML2000:

Advertisement

Quick Links

6
Maintenance ................................................................................................................................. 2
6.1
Introduction .......................................................................................................................... 2
6.1.1
Use and storage in low temperature ............................................................................. 2
6.1.2
Sound pressure values .................................................................................................. 2
6.1.3
Guidelines for evaluating sound pressure levels .......................................................... 3
6.1.4
Changing the communication circuits .......................................................................... 3
6.2
Maintenance for 3U490/3U650/3U650E ............................................................................. 5
6.2.1
Rubber band ................................................................................................................. 5
6.2.2
Installing rubber band with manual advance ............................................................... 5
6.2.3
Rubber band with automatic advance .......................................................................... 5
6.2.4
Installing rubber band for automatic advance .............................................................. 6
6.2.5
Maintenance of main rubber sheet ............................................................................... 6
6.2.6
Rubber in aiming area .................................................................................................. 6
6.2.7
Isolation in front and back targets ................................................................................ 6
6.2.8
Cleaning the microphones ............................................................................................ 7
6.2.9
Changing the microphones ........................................................................................... 7
6.3
Maintenance of 4K300/4K187/4K560 ................................................................................. 8
6.3.1
Parameters for advance of rubber or paper band ......................................................... 8
6.3.2
Mounting rubber or paper on spindle ........................................................................... 8
6.3.3
Mounting the spindle on the target unit ....................................................................... 8
6.3.4
Band guidance .............................................................................................................. 9
6.3.5
Threading the band in the motor mechanism ............................................................... 9
6.3.6
Aiming cards and protection ...................................................................................... 10
6.3.7
Back cover.................................................................................................................. 11
6.3.8
LED lamps for pistol targets ...................................................................................... 11
6.3.9
Changing the microphones ......................................................................................... 12
6.4
Procedures .......................................................................................................................... 13
6.4.1
Preparation for competition ....................................................................................... 13
6.4.2
Annual ........................................................................................................................ 13
6.4.3
Testing precision ........................................................................................................ 13
6.4.4
Adjusting centre ......................................................................................................... 14
6.4.5
Cleaning ..................................................................................................................... 14
02.03.2016 - V13.45
User manual for ML2000
Maintenance

Table of contents

User manual for ML2000
Maintenance
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ML2000 and is the answer not in the manual?

Questions and answers

Summary of Contents for MEGAlink ML2000

  • Page 1: Table Of Contents

    User manual for ML2000 User manual for ML2000 Maintenance Table of contents Maintenance ..........................2 Introduction .......................... 2 6.1.1 Use and storage in low temperature ................2 6.1.2 Sound pressure values ....................2 6.1.3 Guidelines for evaluating sound pressure levels ............3 6.1.4...
  • Page 2: Maintenance

    6 Maintenance 6.1 Introduction This chapter describes how to maintain the ML2000 system. It is important to follow the directions in this chapter in order to keep the system in a condition to meet the requirements also after a period of use.
  • Page 3: Guidelines For Evaluating Sound Pressure Levels

    User manual for ML2000 6.1.3 Guidelines for evaluating sound pressure levels The following guidelines could help in evaluating the sound pressure values: Target/Calibre Normal: Normal: Possible fault: Possible fault: Average Value within Average outside Value outside within 3U490 Big bore...
  • Page 4 User manual for ML2000 Older target circuits must be sent to Megalink for service. 02.03.2016 – V13.45 Maintenance...
  • Page 5: Maintenance For 3U490/3U650/3U650E

    User manual for ML2000 6.2 Maintenance for 3U490/3U650/3U650E 6.2.1 Rubber band The following table indicates the expected number of shots before rubber belt should be mounted or moved. The numbers are strongly dependent upon bullet type and scattering pattern. For this reason the sound pressure values could be a better indicator for the need of maintenance.
  • Page 6: Installing Rubber Band For Automatic Advance

    The Styrofoam in the front target needs to be kept intact. We recommend to replace a square in the centre of the target with a foamed plastic plate. Megalink can deliver these is formats 30x30 cm or 40x40 cm. The foamed plastic can also be used in the back targets (skip glass fibre wallpaper and aiming rubber in the description below) 02.03.2016 –...
  • Page 7: Cleaning The Microphones

    11. Pull out the other plastic film and squeeze the rubber firmly onto the glue 6.2.8 Cleaning the microphones The ML2000 system is not very sensitive to dust and dirt on the microphones. Even a fairly thick layer of dust will not influence on the detection. The sound pressure values will also provide valuable feedback if dirt or particles are interfering the detection.
  • Page 8: Maintenance Of 4K300/4K187/4K560

    User manual for ML2000 6.3 Maintenance of 4K300/4K187/4K560 NB! Never pull hard in the rubber or paper band. This could result in damage to the gear in the motor. Be careful to release the advancing mechanism completely before the band is moved manually.
  • Page 9: Band Guidance

    User manual for ML2000 6.3.4 Band guidance When the spindle is fastened the band should be led into guiding mechanism. This guide differs for the different target models and between paper and rubber. If the band can’t be threaded, the guiding mechanism has to be loosened or removed.
  • Page 10: Aiming Cards And Protection

    User manual for ML2000 6.3.6 Aiming cards and protection The following paragraph describes different solutions for aiming cards, protection and band guidance. 6.3.6.1 Configurations Target Usage Band Adapter Aiming Front 4K187 Air rifle 120mm paper Paper 100mm Paper behind guide...
  • Page 11: Back Cover

    User manual for ML2000 6.3.6.5 4K560 with 250mm band The narrow band s used with a microphone cover with rubber. The band should be inserted under the guide at the top of the cover. The aiming cards are plastic plates mounted in a slot behind the steel cover.
  • Page 12: Changing The Microphones

    User manual for ML2000 The lamp is composed of the following parts: • Cable • Fastening bolts (M5x40) • Steel plate • Rubber sheet and Plastic sheet with LED lamp • Thick O-ring • Inner protection glass without nuts • Outer protection glass with nuts Shots with cal .22 or cal .32 will stop in the outer protection glass.
  • Page 13: Procedures

    User manual for ML2000 6.4 Procedures 6.4.1 Preparation for competition 1. Set up the targets at least 30 minutes before shooting to ensure temperature levelling. 2. Verify that the range management PC is operational and still have free disk space (minimum 50 MB) 3.
  • Page 14: Adjusting Centre

    User manual for ML2000 The requirement for precision and procedure for testing is managed by the individual organisations that are approving targets. 6.4.4 Adjusting centre Verification and/or adjusting the target centre can be done according to the following procedure: 1. Set up the targets at least 30 minutes before testing 2.

Table of Contents