Specifications; Environmental Specifications; Operating Specifications - DirectLOGIC DL405 Manual

24

Specifications

Environmental
Specifications
Operating
Specifications
Operating Temperature
Storage Temperature . . . . . . . . . . . . . . . . . . .
Operating Humidity . . . . . . . . . . . . . . . . . . . .
Air Composition . . . . . . . . . . . . . . . . . . . . . . .
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage Isolation . . . . . . . . . . . . . . . . . . . . . . .
Insulation Resistance . . . . . . . . . . . . . . . . . .
Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Budget Requirement
Maximum number of modules
Location of module . . . . . . . . . . . . . . . . . . . . .
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Voltage . . . . . . . . . . . . . . . . . . . . . .
Input Range . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON input level . . . . . . . . . . . . . . . . . . . . . . . . .
OFF input level . . . . . . . . . . . . . . . . . . . . . . . .
Minimum ON current . . . . . . . . . . . . . . . . . . .
Maximum OFF leakage
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal power consumption
OFF to ON response delay (fast mode)
ON to OFF response delay (fast mode)
OFF to ON response delay (slow mode)
ON to OFF response delay (slow mode)
Interrupt priority . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 0 to 60 C
–20 to 80 C
5 to 95% (non-condensing)
No corrosive gases permitted
MIL STD 810C 514.2
MIL STD 810C 516.2
1500 VAC, 1 minute duration
10M ohms at 500 VDC
NEMA ICS3–304
. . . . . . . . . . . . . 500 ma @ 5 VDC
. . . . . . . . . . . D4–430, 1
D4–440, 2
CPU Base only,
D4–430 –Slot 0 only
D4–440 –1st module, Slot 0
Loose terminal block
26.5 VDC
10.2 VDC to 26.4 VDC, 3.8mA
@ 12 VDC, 8.3mA @ 24 VDC
9.5 mA maximum
9.5 VDC
3.0 VDC
4.0 mA
. . . . . . . . . . . . . . . . . 1.5 mA
2.4k
. . . . . . . . . . . . . 5 VDC, 100mA max.
. . . 0.8 ms to 0.59 ms
. . . 0.15 ms to 0.89 ms
. . 0.88 ms to 6.47 ms
. . 1.64 ms to 9.81 ms
Highest priority: X0
Lowest priority: X7 (if two modules
are used with D4–440, then priority
is X0 – X7, then X20 – X27)
2nd module, Slot 1