Table of Contents
Advertisement
Quick Links
Controller Series E1030/2030/4030
Installation Guide
Controller Series E1030/E2030/E4030
Products
E1030-DP
E2030-DP
E4030-DP
Content
IMPORTANT NOTES FOR E1030/E2030/E4030 SERIES CONTROLLERS .............. 2
SYSTEM OVERVIEW............................................................................................................. 3
E1030 SERIES FUNCTION AND WIRING ......................................................................... 4
POWER SUPPLY AND GROUNDING ................................................................................ 5
DESCRIPTION OF THE CONNECTORS / INTERFACES .............................................. 6
MECHANICAL DIMENSION ................................................................................................. 9
POWER SUPPLY REQUIREMENT ................................................................................... 10
ORDERING INFORMATION ............................................................................................... 10
DECLARATION OF CONFORMITY CE-MARKING ....................................................... 11
ERROR CODES .................................................................................................................... 12
CONTACT ADDRESSES .................................................................................................... 12
NTI AG
Installation: E1030/E2030/E4030 series / 16.09.2005
Page 1/12
Advertisement
Table of Contents
Related Manuals for NTI AG LinMot E1030 Series
Summary of Contents for NTI AG LinMot E1030 Series
-
Page 1: Table Of Contents
DESCRIPTION OF THE CONNECTORS / INTERFACES ..........6 MECHANICAL DIMENSION ....................9 POWER SUPPLY REQUIREMENT ................... 10 ORDERING INFORMATION ....................10 DECLARATION OF CONFORMITY CE-MARKING ............11 ERROR CODES ........................12 CONTACT ADDRESSES ....................12 NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 1/12... -
Page 2: Important Notes For E1030/E2030/E4030 Series Controllers
The information in this documentation reflects the stage of development at the time of press and is therefore without obligation. NTI AG. reserves itself the right to make changes at any time and without notice to reflect further technical advance or product improvement. -
Page 3: System Overview
Linear Motor with internal Position Feedback Complete E4030 Controller based system (E1030 and E2030 controllers will only drive one respectively two motors). Power Supply for Signal and Motor may be the same device (see later). NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 3/12... -
Page 4: E1030 Series Function And Wiring
Controller Series E1030/2030/4030 E1030 series Function and Wiring Picture shows typical wiring of a single axes controller. Multiple axes controller will have additional motor connectors. NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 4/12... -
Page 5: Power Supply And Grounding
Do not switch Power Supply DC Voltage. All power supply switching and E-Stop breaks should be done to the AC supply voltage of the power supply. Failure to observe these precautions may result in severe damage to controller. NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 5/12... -
Page 6: Description Of The Connectors / Interfaces
(In the state ERROR a blink code of the STAT LEDs A and B tells what the actual error is. The blink codes are explained in chapter ‘Service’of the user Manual.) NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 6/12... - Page 7 COM (RS-232) DSUB-9 (male) RS232: 9.6kBaud, use 1:1 connection cable to PC NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 7/12...
- Page 8 Controller Series E1030/2030/4030 Profibus Connector DSUB-9 (female) Isolated 5V output: max 50 mA Profibus ID ID High ID Low ID 1 : Profibus address high ID 2 : Profibus address low NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 8/12...
-
Page 9: Mechanical Dimension
Controller Series E1030/2030/4030 Mechanical Dimension Dimensions Fixings for 2 x M5 screws Centers Recommended mounting for multiple controller installation Fixings for 2 x M5 screws Dimensions in mm NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 9/12... -
Page 10: Power Supply Requirement
Ordering Information Servo Controller Description Art. No. E1030-DP Profibus DP Controller 1 Axis (72V/6A) 0150-1625 E2030-DP Profibus DP Controller 2 Axis (72V/6A) 0150-1626 E4030-DP Profibus DP Controller 4 Axis (72V/6A) 0150-1628 NTI AG Installation: E1030/E2030/E4030 series / 16.09.2005 Page 10/12... -
Page 11: Declaration Of Conformity Ce-Marking
Controller Series E1030/2030/4030 Declaration of Conformity CE-Marking Manufacturer: NTI AG ® LinMot Haerdlistrasse 15 8957 Spreitenbach Switzerland Tel.: +41 (0)56 419 91 91 Fax: +41 (0)56 419 91 92 ® Products: LinMot Controllers Type Art.-No. Type Art-No. Type Art.-No. E1030-DP... -
Page 12: Error Codes
LED is ON l LED blinks shortly (ca. ¼s) off LED is OFF n LED blinks longer (ca. 1½s) Contact Addresses NTI AG LinMot Tel. +41 (0)56 419 91 91 Haerdlistrasse 15 Fax.
Need help?
Do you have a question about the LinMot E1030 Series and is the answer not in the manual?
Questions and answers