Hussmann R3 Installation And Operation Manual
Refrigerated service and/or prep with refrigerated self service front
Hide thumbs
Also See for R3:
- Installation and operation manual (31 pages) ,
- Installation and operation manual (33 pages) ,
- Installation & operation manual (52 pages)
Related Manuals for Hussmann R3
Summary of Contents for Hussmann R3
- Page 1 R3, R3P Refrigerated Service and/or Prep with Refrigerated Self Service Front p/n IGFP-R3, R3P-0208 INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
HUSSMANN CHINO PRODUCT CONTROL The serial number and shipping date of all equipment has been recorded in Hussmann’s files for warranty and re- placement part purposes. All correspondence pertaining to warranty or parts ordering must include the serial num- ber of each piece of equipment involved, in order to pro- vide the customer with the correct parts. -
Page 3: Cut & Plan Views
STUB UP 18" X 18" Service Prep / Self Service Case Scale = 1/2" " Prep Top Area " " " " R3 Options Sushi Service Top and Prep Areas With Two Shelf Self Service Options Self Contained Scale = 1/2"... -
Page 4: Installation
7. To compress silicone at joint, use two Jurgenson wood clamps. Make sure case is level from front to back and side to side on inside bulkheads at joint. 8. Attach sections together via a 2 bolts located in the IGFP-R3, R3P-0208... -
Page 5: Joint Trim
The 3 P-traps must be installed to prevent air leakage and insect entrance into the fixture. NOTE: PVC-DWV solvent cement is recommended. Follow Hussmann’s instructions. INSTALLING CONDENSATE DRAIN Poorly or improperly installed condensate drains can se- riously interfere with the operation of this refrigerator, and result in costly maintenance and product losses. -
Page 6: T-Stat Location
TX Valve. Service Case Temperature Control Temperature control in the upper section of the R3 with the Service Option is done by means of a thermostat and suction solenoid valve. This controls both temperature and... -
Page 7: Plexiglass & Acrylic Care
CLEANING Hussmann recommends using a clean damp chamois, or a paper towel marked as dust and abrasive free with 210 Plastic Cleaner and Polish available by calling Sumner Labs at 1-800-542-8656. -
Page 8: Tips & Troubleshooting
Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the pro- tection required always: 1. -
Page 9: Case Specifications
15° 36° 24° NOTES: These refrigerated merchandisers have been designed for use in stores where temperatures and humidity are maintained at or below 75°F and 55%RH. Stores are responsible for setting their cases appropriately in conditions which vary from the above. The number of defrosts and/or the duration may vary for cases displaying products for which they were not designed. - Page 10 15° 36° 24° NOTES: These refrigerated merchandisers have been designed for use in stores where temperatures and humidity are maintained at or below 75°F and 55%RH. Stores are responsible for setting their cases appropriately in conditions which vary from the above. The number of defrosts and/or the duration may vary for cases displaying products for which they were not designed.
-
Page 11: Schematics
Rev.0208 Schematics Service Top & Refrigerated Front with Single Front Shelf... - Page 12 IGFP-R3, R3P-0208 Schematics...
- Page 13 Rev.0208 Schematics...
- Page 14 IGFP-R3, R3P-0208 Schematics...
- Page 15 Rev.0208 Schematics...
- Page 16 IGFP-R3, R3P-0208 Schematics...
- Page 17 Rev.0208 Schematics...
- Page 18 IGFP-R3, R3P-0208 Schematics...
- Page 19 Rev.0208 Schematics...
- Page 20 IGFP-R3, R3P-0208 Schematics...
-
Page 21: Service Top & Refrigerated Front With Dual Front Shelves
Rev.0208 Schematics Service Top & Refrigerated Front with Dual Front Shelves... - Page 22 IGFP-R3, R3P-0208 Schematics...
- Page 23 Rev.0208 Schematics...
- Page 24 IGFP-R3, R3P-0208 Schematics...
- Page 25 Rev.0208 Schematics...
- Page 26 IGFP-R3, R3P-0208 Schematics...
- Page 27 Rev.0208 Schematics...
- Page 28 IGFP-R3, R3P-0208 Schematics...
- Page 29 Rev.0208 Schematics...
- Page 30 IGFP-R3, R3P-0208 Schematics...
-
Page 31: R3 With Refrigerated Rear Storage
Rev.0208 Schematics R3 with Refrigerated Rear Storage... -
Page 32: Appendices
Hussmann for the installation of each individual type refrigerator. Appendices 1.2 Refrigeration piping should be sized according to Hussmann's equipment recommendations and installed in accordance with normal refrigeration practices. Refrigeration piping should be insulated according to Hussmann’s recommendations. -
Page 33: Appendix D. - Recommendations To User
1.2 Load levels as defined by Hussmann must be observed. 1.3 The best preservation is achieved by following these rules: a) Buy quality products. - Page 34 Make sure that all refrigeration equipment is installed and adjusted in strict accordance with Hussmann’s recommendations. j) See that all storage and refrigeration equipment is kept in proper working order by routine maintenance. IGFP-R3, R3P-0208...
-
Page 35: Limited Warranty
This warranty is made to the original user at the original installation site and is not transferable. Hussmann merchandisers are warranted to be free from defect in material and workmanship under normal use and service for a period of one (1) year from the date of original installation (not to exceed fifteen (15) months from the date of shipment for the factory). -
Page 36: Hussmann ® Chino 13770 Ramona Avenue • Chino, California
The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit. They can be found on a small metal plate on the unit. Please note them below for future reference. MODEL: SERIAL NUMBER: IGFP-R3, R3P-0208...
Need help?
Do you have a question about the R3 and is the answer not in the manual?
Questions and answers