EACON EC5000 Series User Manual
  1. Manuals
  2. Brands
  3. EACON Manuals
  4. DC Drives
  5. EC5000 Series
  6. User manual

EACON EC5000 Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Manufacturer:
Website:www.eacon.cc
E-mail:overseas@eacon.cn
AC Motor Driver
Read below information before use
Description of Functional Parameter
The diagnosis and the exclusion for the abnormalities
V2.5
Installation and Wire Layout
Operation and inspection
Operation keypad Panel
MODBUS Communication Protocol
Maintenance inspection
Appendix
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents
loading

Related Manuals for EACON EC5000 Series

Summary of Contents for EACON EC5000 Series

  • Page 1 AC Motor Driver V2.5 Read below information before use Installation and Wire Layout Operation and inspection Operation keypad Panel Description of Functional Parameter MODBUS Communication Protocol The diagnosis and the exclusion for the abnormalities Maintenance inspection Appendix Manufacturer: Website:www.eacon.cc E-mail:overseas@eacon.cn...
  • Page 2 Introduction Thank you for using EC5000 Series AC drive. EC5000 Series is a high-performance / low noise general-purpose AC drive,manufactured using high-quality components and incorporating the latest micro- processor technology available. This manual describes the matters relevant to the installation, parameters setting, abnormality diagnosis and solution, and the daily maintenance of the AC drive that need attention of the users.

  • Page 3: Table Of Contents

    Catalogue EC5000 TABLE OF CONTENTS Chapter 1 Read Below Information Before Use Warning! 1.1 Delivery Inspection 1.Please do not test the voltage resistance of the interior components 1.2 Transport of the driver, as the semiconductor of the driver is easy to be punctured 1.3 Storage and damaged by high voltage.

  • Page 4: Chapter 1 Read Below Information Before Use

    EC5000 EC5000 Catalogue Read below information before use 1.1Delivery Inspection 6.2.2 Function Code and Data Content 6.3 Error Value Every EC5000 AC drive has pass by strict quality management before 6.4 Communication Protocol and Digital Address Definition delivery, and been packed to enhance its collision resistance. The customer Chapter 7 The Diagnosis and the Exclusion for the Abnormalities should immediately inspect the following inspection steps after unpacking the 7.1 List of Protective Actions...

  • Page 5: Transport

    EC5000 EC5000 Read below information before use Read below information before use Description of the label of product 1.3 Storage EC500D4G23~EC50132G23 EC50D75G43~EC50560G0630P43 This product must be in the packing box before installation. If it won’t be used for a period, in order to keep it within the warranty of our company and for 1.AC drive Model the future maintenance, the following matters must be paid attention to for the 2.Input power Spec.

  • Page 6: Considerations For Choices Of Ac Drives

    EC5000 Read below information before use EC5000 Read below information before use 4.When the AC drive is installed in the installation or control panel but Parameter Setting isn’t used, especially in the construction sites or the wet places with lots 1.Because of the highest speed for the digital operation can reach to of dust, the AC drive should be removed and put in a proper environment 400Hz,so when it use in the highest speed place, it can use the speed...

  • Page 7: Chapter 2 Installation And Wire Layout

    EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout 2.1 Installation Environment ■When the AC drive is installed in the control panel, ventilation and heat dissipation shall be considered to ensure that the ambient Please install the AC drive in the following environment to guarantee temperature of the AC drive does not exceed the specification value.
  • Page 8 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout unit:mm Frame40：EC50015G23B、EC518D5G23B、EC50022G23B Frame11：EC502D2G23C、EC503D7G23C Frame20：EC505D5G23B Frame50：EC50030G23B、EC50037G23B Frame30：EC507D5G23B、EC50011G23B - 8 - - 9 -...

  • Page 9: Installation Dimension Of Ac Drive

    EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout Frame60：EC50045G23B、EC50055G23B Frame80：EC50110G23B、EC50132G23B 2.3.2 400V Installation dimension of AC drive Frame70：EC50075G23B、EC50090G23B unit:mm Frame10： EC50D75G43C、EC501D5G02D2P43C - 10 - - 11 -...
  • Page 10 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout unit:mm unit:mm Frame11： EC502D2G03D0HP43C、EC503D0G04D0P43C、EC504D0G05D5P43C Frame30： EC50011G0015P43C、EC50015G18D5P43C Frame40： EC518D5G0022P43B、EC50022G0030P43B Frame20： EC505D5G07D5P43C、EC507D5G0011P43C ： Frame50 EC50030G0037P43B、EC50037G0045P43B - 12 - - 13 -...
  • Page 11 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout unit:mm unit:mm Frame60:EC50045G0055P43B、EC50055G0075P43B Frame90:EC501060G185P43B、EC50185G0220P43B Notice: The base is optional Frame70:EC50075G0090P43B、EC50090G0110P43B FrameA0:EC50250G0280P43B、EC50280G0315P43B、EC50315G0350P43B EC50350G0400P43B Notice: The base is optional Notice: The base is optional Frame80:EC50110G0132P43B、EC50132G0160P43B FrameB0:EC50400G0450P43B、EC50450G0500P43B、EC50500G0560P43B、 EC50560G630P43B Notice: The base is optional Notice: The base is optional - 14 - - 15 -...

  • Page 12: Instruction For Wire Layout

    EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout unit:mm ■After finishing the wire layout, check the following things: Dimension of the installation hole on the external frame of operation panel 1. Are all the connections correct? 2. Is there any connection left out? 101.2 3.
  • Page 13 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout Basic Wiring Diagram 2 Basic Wiring Diagram1 EC505D5G07D5P43B~EC50015G18D5P43B EC500D4G23C~EC50132G23A、EC50D75G43C~EC504D0G05D5P43C DC Reactor (Optional component) Brake resistor(optional component) Brake resistor(optional component) Short Circuit Plate (Default Setting) Brake Resistor(Optional Component) Non-fuse breaker Non-fuse breaker R / L1 R / L1 U / T1...
  • Page 14 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout 2.4.2 Control Terminal Connections Basic Wiring Diagram 3 EC518D5G0022P43B~EC50560G0630P43B symbol Sort Terminal name Function potentiometer potentiometer power（+10VDC） Brake resistor Brake unit (optional component) for setting frequency（1～10kΩ） power DC Reactor (Optional component) Short Circuit Plate (Default Setting) 1.
  • Page 15 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout Go through in-phase and encirle 3 loops or above symbol Sort Terminal name Function Output monitor signal of simulated FV/FI voltage 0～+10VDC Choose one of the following choices as the monitoring target： 0.output frequency(10V/max Simulate monitor Simulate...
  • Page 16 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout The main wiring diagram of EACN AC DRIVE Diameter Diameter Input Voltage Motor Type of main of control breaker A wire mm² wire mm² - 24 - - 25 -...

  • Page 17: System Wiring Diagram

    EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout 2.4.4 Connection of the Main Loop Terminals 2.4.3 System Wiring Diagram Description of the Main Loop Terminals Please use the power supply in accordance with the rated Power supply specification in the usage Description No.
  • Page 18 EC5000 EC5000 Installation and Wire Layout Installation and Wire Layout ■Please do not connect the AC with the output terminal (U/T1, V/T2 and W/T3) of AC drive;otherwise it may cause AC drive damage. ■Ensure that the screws of the main loop terminals are tightened to prevent the sparks caused by the loose screw due to vibration.

  • Page 19: Chapter 3 Operation And Inspection

    EC5000 EC5000 Installation and Wire Layout Operation and inspection Grounding terminals of AC drive (EG) 3.1 Check and Test Before Operation ■ For safety and noise reduction, the grounding terminals of AC drive should be well grounded. The following matters should be paid attention before the operation: ■The grounding wire of AC drive can’t be grounded together with the ■...

  • Page 20: Test Run

    EC5000 EC5000 Operation and inspection Operation Keypad Panel 4.1 LED Keyboard Panel Appearance and 3 Test Run Operation Process If no abnormality is detected after the inspection and preparation before the 8 segment digital tube LED operation panel by six and seven leds, it can operation according to 3-1, the test run can be performed.

  • Page 21: Appearance & Operation Procedure Of Lcd Keypad Panel

    EC5000 EC5000 Operation Keypad Panel Operation Keypad Panel Functions of key combinations: POWER DATA SETTING: ： STOP Hold down the keys at the same time to LOCAL STOP （EXAMPLE：change first frequency to：50.00Hz） (LOCAL) and REMOTSwitch between (remote). ： STOP In the state of LOC panel, hold down the key and the STOP key to enter or exit the JOG state.

  • Page 22: Lcd Keyboard Panel Appearance

    EC5000 EC5000 Operation Keypad Panel Operation keypad Panel The frequency set 4.2.1 LCD Keyboard Panel Appearance ① LOC, REMx shows an effective source of control. ② FWD, REV shows the direction of rotation at run time. The frequency set ③ RUN, STOP indicates the running status of AC drives.
  • Page 23 EC5000 EC5000 Operation keypad Panel Operation keypad Panel Operations like parameter setting/ operation data/ maintenance information/ fault information / data copy FUNCTION DATA SETTING Under the initial screen press into the frame, the rotary encoder to (e.g. the max frequency is altered to: 55.00Hz) select feature, press the key to enter the function menu, press the ENTER...

  • Page 24: Chapter 5 Description Of Functional Parameter

    EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter 5.1 Function Parameter List Setting Default Page Address Function Parameters Name Description Range Setting Default Page Address Function Parameters Name Description Model A18 Acceleration Range Unit:0.1s (1s for 1000s and above) dependent time 1 A00 Macro...
  • Page 25 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Parameters Parameters Setting Setting Default Page Address Default Page Address Function Description Function Description Name Name range range JOG acceleration time, the max External control instruction 6 or A48 JOG accele- frequency:100% multi-speed control step 6 more...
  • Page 26 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Parameters Parameters Setting Setting Default Page Address Default Page Address Function Description Function Description Name Name range range 14:Frequency reference loss The setting value 1,2,4-6: 15:Transmission data output 1 The carrier frequency=The setting 16:Transmission data output 2 value x 2.5KHz B10 Y3 Function...
  • Page 27 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Parameters Parameters Setting Setting Default Page Address Default Page Address Function Description Function Description Name Name range range D05 PID Set D control proportion increase. The AC drive is in sleep mode. Derivative time If set to be 0.0, no D control.
  • Page 28 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Parameters Parameters Setting Setting Default Page Address Default Page Address Function Description Function Description Name Name range range Rotation difference compensation is Unit:1% C26 Input phase increasing AC drive output When setting is 100%,this function C15 Slip frequency by propotion of motor...
  • Page 29 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Parameters Parameters Setting Setting Default Page Address Default Page Address Function Description Function Description Name Name range range F06 Stop Only LED manipulator has this 0:Ramp to stop-Decel 1(fault) method functional code Radiator 1:Coast to stop(fault)

  • Page 30: Detailed Description Of Functional Parameters

    EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Parameters Setting Default Page Address Function Description Name range 5.2 Detailed Description of Functional disconnect S1 is stop. S2 rise along the pulse switch and reversing. Parameters Three wires mode: S1 rising along F23 Wire Auxiliary the trigger, disconnect S2 is stop, S3...
  • Page 31 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter setting Select running order Select frequency order In running order OFF in right and opposite direction, motor retards in retard time 1(A19), and brakes to stop by direct current. If short brake From control panel From serial communication time and big inertia capacity,there will be over voltage(OU)error during...
  • Page 32 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter SETTING3: slide to stop with second retard time A.motor voltage and frequency property B.the highest running speed of the motor Select increase/decrease speed 2(example)  Only select high start moment of force on the following circumstance: (Usually not necessary) A.long connecting wire(150m or longer) deceleration time...
  • Page 33 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter A18 Accel time1 setting limits: 0.0-3600s factory default: *3 Set special mode when motor(high speed motor) or machinery need special rotation moment of force adjustment. A19 Decel time1 setting limits: 0.0-3600s factory default: *3 A20 Accel time2 setting limits: 0.0-3600s...
  • Page 34 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter The value of Parameter A35 must be higher than the lower limit of the output Positive rotation frequency of Parameter A36. 100% is the setting value of Parameter A11. Run instruction The upper limit of output frequency = (A11*A35)/100 Reverse rotation Run instruction...
  • Page 35 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter A40 Running mode setting limits:0~3 factory default:0 FUNCTION SET VALUE RUNNING(SET)VALUE A41 Step 1 mode setting limits:F1~R4 0~4000S factory default:F1 0S ————— A40 mode running A42 Step 2 mode setting limits:F1~R4 0~4000S factory default:F1 0S A41 step 1 mode F1 10.0S A27 main Frequency...
  • Page 36 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter B01 Terminal S2 sel setting limits:0~26 factory default:0 B02 Terminal S3 sel setting limits:2~26 factory default:2 Name Illustration B03 Terminal S4 sel setting limits:2~26 factory default:4 Accelerate/retard time selection B04 Terminal S5 sel setting limits:2~26 factory default:9 2/RT2...
  • Page 37 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Notice!  Set 0，1： Combination ON/OFF switch of terminal function S5、 S6 and S7 can Run sw （a contact） Stop sw Positive run(stop when “open”) (b contact) select 1-7 multistage frequency and JOG frequency. The undefined terminal Run instruction(run when“closed”) of function terminal S5、S6 and S7 act as OFF.
  • Page 38 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Analog Input Combined signal input Selected time of accelerating Fref and reducing speed 14（RT2） 13（RT1） A18 1 accelerate，A19 1 decelerate speed 100ms 100ms A20 2 accelerate，A21 2 decelerate speed A22 3 accelerare，A23 3 decelerate speed A24 4 accelerate，A25 4 decelerate speed ■Set 27:UP/DOWN order（set:B07=27）...
  • Page 39 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter speed limit though there is no UP/DOWN order. ■ NAME ILLUSTRATION If input jog and start order during running with UP/DOWN order, the jog and start order has priority. switch off when AC drive output is off BB(base level blockade) switch off when select panel operation running mode...
  • Page 40 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter ■ Setting: 3，setting example of “any frequency unamious signal” Notice! Released width Detection width When B16 is 0, frequency is kept although AC drive power is off. Detection result of expected frequency B17 frequency lost setting limits：0～1...
  • Page 41 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter ■ Examples In order to monitor,send the output Frequency and the output current to the AC drive runs in 0%-100% frequency order when the input voltage is 0-5V. simulate output terminal FMA-FC Increase: B18=200,deviation:B19=0 ■F M A function：...
  • Page 42 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Frequency test mulit-function joint input set to be “4”（Frequency output≤ CARRIER WAVE METAL NOISE DISTURB NOISE AND Frequency test standard） （KHZ） FROM MOTOR LEAKAGE CURRENT 12 Fout Discharge rate 24 Fout -2Hz less 36 Fout...
  • Page 43 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter C07 auto-retry setting limits：0～10 factory default：0 Notice! Keep running order to continue running from instant power off.. Set AC drive self diagnose and restart times when error occours. Set AC drive re-start and error test resume after error occured. Auto dia- C03 SpdSrch Current setting limits：0%～200% factory default：110%...
  • Page 44 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter If stop mode(A05)selected to be slide to stop, AC drive don't execute Usually don't need to adjust rotation moment of force compensation(factory DC braking when AC drive stops. setting C12:1.0)Rotation moment of force need to be adjusted when connection wire between AC drive and motor is too long or motor vibrating.
  • Page 45 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter 3 ：AC drive motor （time constant 8 minutes） Set speed loss protecting action standard with unit of 1% and AC drive 4 ：AC drive motor （time constant 5 minutes） rated current 100%. Electronic overheat protection is monitoring motor temperature to protect it setting limits：0 ～4 C23 rotation moment of force test...
  • Page 46 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter C29 SPO delay setting limits：0.0S～2.0S factory defaut：0.2S 1.voltage signal of control circuit terminal FV(0-10): select(A03) to be 2 or 3 to set running direction. Set output missing test time 2.frequency order data(A27-A34): select(A03) to be 0 or 1 to set running C30 power selection factory defaut：*3 direction (combination of multi-function joint, multi-pace speed order and jog/...
  • Page 47 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter PID Control Function Block Diagram D12 Pump Control setting limits:0~3 factory default:3 0~2:The number of opening pumps in the constant pressure water Target value supply control Limit Limit value value 3:close the pump control Gain D02 for adjusting...
  • Page 48 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter E01 energy saving selection setting limits：0～1 factory default：0 E05 calculating time setting limits：1～200 factory default：1 E02 energy saving increase setting limits：0.00～655.00 factory default:*3 Set average power calculating time in energy saving mode. E03 60Hz voltage setting limits：0～120% factory default：50%...
  • Page 49 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter ■band： F09 L / R sellection setting limits：0～1 factory default：0 0： 1200BPS 1： 2400BPS 2： 4800BPS 0：When LOCAL/REMOTE shifting, re-run is valid when stop order is inputed 3： 9600BPS 4: 19200BPS 1：When LOCAL/REMOTE shifting, re-run is valid at once 5: 38400BPS ■...
  • Page 50 EC5000 EC5000 Description of Functional Parameter Description of Functional Parameter Only LCD manipulator has this functional code 3:increase five items which monitored above 1&2 0: setting frequency F16 Low-speed sel(Pr_F15) setting limits:0~2 factory default:0 1: output frequency Set the input voltage of the AC drive. According to this set value, the 2: output current AC drive can switch the voltage protection level.
  • Page 51 Second wires mode: connect S1 is foreward, disconnect S1 is stop. S2 level switch and reversing. EC5000 Series of AC drive adopts the communication protocol of Modbus Three wires mode: S1 rising along the trigger is foreward, disconnect networks. Modbus can adopt two data coding modes: either ASCII (American S2 is stop, S3 rising along the trigger is reversal Standard Code for Information Interchange) or RTU (Remote Terminal Unit).

  • Page 52: Chapter 6 Modbus Communication Protocol

    EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol 6.1 Communication Data Structure: (1)7N2 For ASCII F03=0 6.2 Data Format Frame Stop bit Stop bit Start bit ■ ASCII Mode: 7- data bits Character String Starting Character = ‘: ’ (3AH) 10 bits Character Frame Length Address Hi Communication Address:...
  • Page 53 EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol 1.ASCII Mode: Inquiry Message Character String Format Response Message Character String Format: ‘: ’ ‘: ’ ‘0’ ‘0’ Address Address ‘1’ ‘1’ ‘0’ ‘0’ Function Function 6.2.1 Communication Address (Address) ‘3’ ‘3’ 00H: Broadcast to all drivers;...
  • Page 54 EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol ■ Command Code: 08H, Communication Loop Test Function Code 06H: Write data to register ■ This command is used to test the communication status between the For example: as for Driver with Address 01H, write 6000(1770H) to the controller device (usually PC or PLC) and drivers, and the drivers will send internal setting parameter of driver 001DH The data content received back to the controller device without any operation.
  • Page 55 EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol ■ 2.RTU Mode: Command Code: 10H, Write several data in succession Inquiry Message Format: For example: Change the multiple speed setting of driver (Address 01H) Response Message Format: 001DH=50.00(1388H) and 001EH=40.00(0FA0H) 1. ASCII Mode: Data Data Inquiry Message Format:...
  • Page 56 EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol Step 4: Check the value after right shift: if it is “0”, save the new value 6.4 Definitions of Parameter Word Address obtained in Step 3 to CRC register, or, Exclusive OR A001H and CRC in Communication Protocol register, and then save the result to CRC register.
  • Page 57 EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol Parameter Function Description Definition Word ■Additional Response for Communication error: Address Bit9 Running Mode Bit1 When driver is connected for communication, if an error occurs, the driver will Bit10 Running Mode Bit2 respond with error code and set the most significant bit (bit7) of command code to “1”.
  • Page 58 EC5000 EC5000 MODBUS Communication Protocol MODBUS Communication Protocol Parameter Parameter Function Description Function Description Definition Word Definition Word Address Address 2101H Bit14~15 0FH=EF2 E=Reserved 010H=EF3 IO Status Code Bit0 012H=EF4 Bit1 013H=EF5 Bit2 014H=EF6 2100H Bit3 015H=SP| Bit4 016H=Spo Bit5 017H=CE 2102H Bit6...
  • Page 59 EC5000 EC5000 The diagnosis and the exclusion for the abnormalities The diagnosis and the exclusion for the abnormalities 7 .1List of Actions to Protect Fault Description detail error correction The AC drive itself has the functions of over-voltage, low voltage and The output current of AC Check the three over-current alarms and protection.
  • Page 60 EC5000 EC5000 The diagnosis and the exclusion for the abnormalities The diagnosis and the exclusion for the abnormalities Fault Description detail error correction Fault Description detail error correction Try the function of Check the input "A01 factory Error from external,if the error EEPROM error AC drive control defaults",if it is still...
  • Page 61 EC5000 EC5000 The diagnosis and the exclusion for the abnormalities The diagnosis and the exclusion for the abnormalities Notice! display Content illustration When inputting the right/opposite operation order, the AC drive fails The input multifunction function(B01-B07) have to receive the failure resetting signal. You must cut off the right/opposite The setting of the one of the following setting fault: operation order first, and then reset.
  • Page 62 EC5000 EC5000 The diagnosis and the exclusion for the abnormalities The diagnosis and the exclusion for the abnormalities cannot be followed, corresponding measures or solutions must be taken. transforming in order to reduce the higher harmonics composition. As is 1.Avoid vibrations, and use vibration-proof pads when necessary. shown in the figure: Make sure that the vibration is under regulation.
  • Page 63 EC5000 EC5000 Maintenance inspection Maintenance inspection AC drive consists of multiple parts including electronic parts such as operation with cover removed begin. ICs, resistors, capacitors and transistors as well as cooling fans and 2.No one other than the appointed operators could perform relays and so on.
  • Page 64 EC5000 EC5000 Maintenance inspection Maintenance inspection Spot Spot Check Inspection Items Inspection Method Check Inspection Items Inspection Method Cheeck site Cheeck site Period Period Has the safety valve loose? Half Is it stained with dus t or Mechanism With eye survey Daily With eye survey Is there significant inflation...
  • Page 65 EC5000 EC5000 Appendix Appendix Appendix A-1 Product Specifications Output Suited Output Power Input Voltage Current Motors Model Capacity G/P(KW) Product Standard Specifications Schedule G/P(A) G/P(KW) Output Output Suited Power Single/Three 90/- 126/- 346/- 90/- EC50090G23 Input Voltage Current Motors Model Capacity G/P(KW) Phase 200V 50Hz...
  • Page 66 EC5000 EC5000 Appendix Appendix Appendix A-2 Product Technical Indexes Output Suited Series EC5000 Output Power Input Voltage Current Motors Model Capacity G/P(KW) G/P(A) G/P(KW) Rated Voltage 400V/50Hz/60Hz, Voltage:±15%; Frequency:±5% Input Three Phase EC50055G0075P43 55/75 98/130 128/165 55/75 and Frequency 200V/50Hz/60Hz, Voltag e:±15%;Frequency:±5% 400V 50Hz Three Phase EC50075G0090P43...
  • Page 67 EC5000 Appendix EC5000 Appendix Series EC5000 Appendix B - 1 Optional Digital Operators and External Components General Model(G): About 250% AC drive rating current ■ LED Operator PU-01 Instantaneous Over Current Blower/Pump Model(P): About 200% AC drive rating current General Model(G): 150% rating output current for 1min Performance before sliding stop Over Load...
  • Page 68 EC5000 Appendix EC5000 Appendix Appendix B - 2 Optional Product Base Installation Dimension Drawing Structure90:EC50160G0185P43B、EC50185G0220P43B、EC50220G0250P43B Structure70:EC50075G0090P43B、EC50090G0110P43B StructureA0:EC50250G0280P43B、EC50280G0315P43B、EC50315G0350P43B Structure80:EC50110G0132P43B、EC50132G0160P43B EC50350G0400P43B - 128 - - 129 -...
  • Page 69 EC5000 Appendix EC5000 Appendix StructureB0:EC50400G0450P43B、EC50450G0500P43B、 EC50500G0560P43B、EC50560G0630P43B Appendix B-3 Braking Resistor Braking Resistor Selection schedule Resistor Specifications Suited Suited Braking Motor /KW Motor /KW AC Drive Model Torque% Resistance Power W Model G Model P Ω - 130 - - 131 -...
  • Page 70 EC5000 Appendix Appendix EC5000 Appendix C-1the given frequency and operation panel of the external potentiometer 1.The wiring diagram(1-1) of the external potentiometer terminals A、B、C，usually choose 5-10K potentiometer,we can adjust terminal C to judge the potentiometer. Use the resistance of the multimeter to measure any two terminals A、B、C,the biggest resistance is terminal A、B,the left one is the terminal C which can judge the potentiometer.
  • Page 71 EC5000 EC5000 Appendix Appendix The frequency is setted by A27,B01=0, choose the operation mode The frequency is setted by A27,B01=1, A03=1,F23=2; A03=1. 3.Action description (3) Action description When trigger S1,the inverter starts; trigger S3, the inverter reverse operation When the switch A close,the inverter forwards;when it is opened,the When press STOP, the inverter stops.
  • Page 72 ZHE JIANG EACN ELECTRONIC TECHNOLOGY CO.,LTD. Address:No.1 Jinhe Road, Qinshan Street, Haiyan County, Jiaxing City, Zhejiang Province . 6.Please make sure to keep this card and show it to the maintenance Website: www.eacon.cn E-mail: overseas@eacon.cc unit during warranty. 7.This agreement shall be interpreted by ZHEJIANG EACN ELECTRONIC THCHNOLOGY CO., LTD.

This manual is also suitable for:

Ec500d4g23Ec50132g23Ec50d75g43Ec50560g0630p43

Table of Contents