Hussmann CIDM-I Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Hussmann Manuals
  4. Merchandiser
  5. CIDM-I
  6. Installation and operation manual
Hussmann CIDM-I Installation And Operation Manual

Hussmann CIDM-I Installation And Operation Manual

Refrigerated self-service island display
Hide thumbs
Table of Contents

Advertisement

Quick Links

CIDM-E
CIDM-I
p/n IGIC-CIDM-0508
INSTALLATION & OPERATION GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Hussmann CIDM-I

Summary of Contents for Hussmann CIDM-I

  • Page 1 CIDM-E CIDM-I p/n IGIC-CIDM-0508 INSTALLATION & OPERATION GUIDE...

  • Page 2: Table Of Contents

    Hussmann Chino product Control The serial number and shipping date of all equipment has been recorded in Hussmann’s files for warranty and replacement part purposes. All correspondence pertaining to warranty or parts ordering must include the serial number of each piece of equipment involved, in order to provide the customer with the correct parts.

  • Page 3: Cut And Plan Views

    Rev. 0508 Cut and plan views 29 1/2” 6” 9” 11” 3 11/16” 40 13/16” 3 11/16” 48 3/16” CIDM ISLAND CIDME CIDMI 3 1/16” 10’ 12 13/16” 30 3/8” 33’ 27’ 34 7/8” 36’...

  • Page 4: Installation

    Location The refrigerated merchandisers have been designed for use only in air conditioned stores where temperature and humidity are maintained at or below 75°F and 55% relative humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or windows (etc.) to create air currents around the merchandiser, as this will impair its correct operation.

  • Page 5: Joint Trim

    Rev. 0508 Joint Trim After cases have been leveled and joined, and refrigeration, electrical, and wasted piping work completed, install the splashguards. Fasten along the top edge, or center, with #10 X 3/3” sheet metal screws. DO nOT SeAL JOInT TRIM TO FLOOR! After Joint Trim Case to Floor sealing After case has been leveled and joints are properly covered...

  • Page 6: Refrigeration

    Refrigerant Type The standard refrigerant will be R- unless otherwise specified on the customer order. Check the serial plate on the case for information. piping The refrigerant line outlets are located under the case. Locate first the electrical box, the outlets are then on the same side of the case but at the opposite end.

  • Page 7: Electrical

    Actual ampere draw may be less than specified. Field wiring from the refrigeration control panel to the merchandisers is required for refrigeration thermostats. Most component amperes are listed in the “Case Specs” section, but always check the serial plate.

  • Page 8: User Information

    Hussmann cases were not designed to “heat up” or “cool down” product - but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the protection required always: 1.

  • Page 9: Plexiglass And Acrylic Care

    Cleaning Hussmann recommends using a clean damp chamois, or a paper towel marketed as dust and abrasive free with 210 plastic Cleaner and polish available by calling Sumner Labs at 1-800-542-8656.

  • Page 10: Electrical Wiring Diagrams

    CIDME CIDME w OMNISTAT CIDMI-3 CIDMI-3 w OMNISTAT CIDM-I-R CIDM CIDM-I-SC CIDM-I-R Hot Gas CIDM-I-R Hot Gas CIDM-E-R CIDM-I-3-R Insert Case electrical Wiring Diagrams 4’X3’ 14’ 14’ 14’ 10’ 3’ IGIC-CIDM-0508 W0300006 W0300008 W0300007 W0300009 W0300017 W0300018 W0300019 W030000 W030001...

  • Page 11: Wiring Diagrams

    Rev. 0508 Wiring Diagrams ZONE EVAP. DEF. COMM. COMP.
  • Page 12 IGIC-CIDM-0508 Wiring Diagrams (Cont'd) BLACK...
  • Page 13 Rev. 0508 Wiring Diagrams (Cont'd) ZONE EVAP. DEF. COMM. COMP.
  • Page 14 IGIC-CIDM-0508 Wiring Diagrams (Cont'd) BLACK...
  • Page 15 Rev. 0508 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 Wiring Diagrams (Cont'd) B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST BLUE BLUE B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST BROWN BROWN B432PUNVHP-A WHITE...
  • Page 16 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 Wiring Diagrams (Cont'd) BLUE BLUE BROWN BROWN BROWN BROWN IGIC-CIDM-0508 B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST B432PUNVHP-A...
  • Page 17 Rev. 0508 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 Wiring Diagrams (Cont'd) B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST BLUE BLUE B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST BROWN BROWN B432PUNVHP-A WHITE...
  • Page 18 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-1072 F25/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 125-03-0007 F15/T8/SPX30 Wiring Diagrams (Cont'd) BLUE BLUE BROWN BROWN BROWN BROWN IGIC-CIDM-0508 B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST B432PUNVHP-A WHITE MAGNETE BLACK 125-01-3273 BALLAST B432PUNVHP-A...
  • Page 19 Rev. 0508 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1073 F32T8-48" 125-03-1072 F25T8-36" 125-03-1072 F25T8-36" 125-03-1072 F25T8-36" 125-03-1072 F25T8-36" 125-03-1072 F25T8-36" 125-03-1072 F25T8-36" 125-03-1071 F17T8-24" 125-03-1071 F17T8-24" 125-03-1071 F17T8-24" 125-03-1071 F17T8-24" 125-03-1071 F17T8-24" 125-03-1071 F17T8-24"...
  • Page 20 125-03-1073 125-03-1073 F32T8-48" F32T8-48" 125-03-1073 125-03-1073 F32T8-48" F32T8-48" 125-03-1073 125-03-1073 F32T8-48" F32T8-48" 125-03-1073 125-03-1073 F32T8-48" F32T8-48" 125-03-1071 125-03-1071 F17T8-24" F17T8-24" 125-03-1071 125-03-1071 F17T8-24" F17T8-24" 125-03-1071 125-03-1071 F17T8-24" F17T8-24" 125-03-1071 125-03-1071 F17T8-24" F17T8-24" 125-03-1071 125-03-1071 F17T8-24" F17T8-24" 125-03-1071 125-03-1071 F17T8-24" F17T8-24" 125-03-1071 125-03-1071 F17T8-24"...
  • Page 21 Rev. 0508 Wiring Diagrams (Cont'd) LH3-120-L FULHAM 125-01-3266 BALLAST LH4-120-L FULHAM 125-01-3267 BALLAST...
  • Page 22 Wiring Diagrams (Cont'd) LH3-120-L FULHAM 125-01-3266 BALLAST LH4-120-L FULHAM 125-01-3267 BALLAST IGIC-CIDM-0508...

  • Page 23: Sporland Omnistat Time Clock Program Settings

    Rev. 0508 Sporland Omnistat Time Clock program Settings Display parameter pASSWORD pROBe pARAMeTeRS ambient probe calibration (x 0.1°C/°F) Measurement stability probe display: 0 = regulation probe, 1 = product food probe (second probe) °C/°F (0=°C, 1=°F) ReGULATOR pARAMeTeRS Regulating differential (hysteresis 0=0.5 °C/ °F) Minimum allowable set Maximum allowable set Cr1 17 °C/°F 60 Enabling Ed alarm: max duration of defrost is reached (0 = no, 1 = yes)
  • Page 24 Sporland Omnistat Time Clock program Settings (Cont'd) SAFeTY STAnDARD: in compliance with the european laws. Installation precautions • the connection cables should be suitable for up to 195°F operation; Caution: Low voltage and probe wiring must be properly separated from high voltage wiring DISpLAY During normal working conditions, the display shows the value measured by the air regulation probe or by the second probe (parameter /4).

  • Page 25: Appendices

    They are based on confirmed field experience over many years. 1.1 The installer is responsible for following the installation instructions and recommendations provided by Hussmann for the installation of each individual type refrigerator. Appendices 1. Refrigeration piping should be sized according to the equipment manufacturer’s recommendations...

  • Page 26: Appendix C. - Field Recommendations - Refrigerated

    11. Is the store ambient over 75°F, 55% RH as set forth in ASHRAE Standard 7 and ASHRAE Standard 117? 1. Are the shelf positions, number, and size other than recommended by Hussmann? 13. Is there an improper application or control system? 14. Is the evaporator fan motor/blade inoperative? 15.

  • Page 27: Appendix D. - Recommendations To User - Refrigerated

    Buy quality products. b) Receive perishables from transit equipment at the ideal temperature for the particular product. For further technical information, please log on to http://www.hussmann.com/products/CIDM.htm Appendices (Cont'd) c) Expedite perishables to the store’s storage equipment to avoid unnecessary warm-up and prolonged temperature recovery.
  • Page 28 __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ Additional copies of this publication may be obtained by contacting: Hussmann® Chino 13770 Ramona Avenue • Chino, California 91710 (909) 68-894 FAX (909) 590-4910 (800) 395-99 /Chino The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit.

This manual is also suitable for:

Cidm-eChino cidm-iChino cidm-e

Table of Contents