Hoshizaki KM-600MAH Instruction Manual
Modular crescent cuber
Hide thumbs
Also See for KM-600MAH:
- Service manual (45 pages) ,
- Parts list (21 pages) ,
- Instruction manual (19 pages)
Related Manuals for Hoshizaki KM-600MAH
Summary of Contents for Hoshizaki KM-600MAH
- Page 1 Hoshizaki America, Inc. “A Superior Degree of Reliability” www.hoshizaki.com Modular Crescent Cuber Model KM-600MAH INSTRUCTION MANUAL ™ Issued: 6-24-2008 Revised: 7-23-2008...
- Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write, or send an e-mail message to the Hoshizaki Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
This manual should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that may be necessary. -
Page 4: Specifications
I. Specifications A. Nameplate Rating 1. KM-600MAH (air-cooled) MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR PUMP OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER(USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE REFRIGERANT MOTOR-COMPRESSOR THERMALLY PROTECTED, ICE MAKER WITHOUT STORAGE MEANS See the nameplate for electrical and refrigeration specifications. -
Page 5: Dimensions / Connections
B. Dimensions / Connections 1. KM-600MAH... -
Page 6: Installation And Operating Instructions
6) See the nameplate on the rear panel, and check that your voltage supplied corresponds with the voltage specified on the nameplate. 7) This icemaker needs a storage bin. The recommended storage bin is Hoshizaki Ice Storage Bin, Model B-300 series. -
Page 7: Location
C. Location 1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°C); Normal operating water temperature should be within +45°F to +90°F (+7°C to +3°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect icemaker performance. -
Page 8: Electrical Connection
E. Electrical Connection 1. Electrical connection must be made in accordance with the instructions on the "WARNING" tag, provided with the pig tail leads in the junction box. . Electrical connections must meet national, state, and local electrical code requirements. Failure to meet these code requirements could cause severe injury to individuals or extensive damage to equipment. -
Page 9: Water Supply And Drain Connections
F. Water Supply and Drain Connections See Fig. 4 To prevent damage to equipment, do not operate the icemaker when the water supply is off, or if the pressure is below 10 PSIG. Do not run the icemaker until the proper water pressure is reached. •... - Page 10 KM-600MAH Icemaker Icemaker Water Supply Inlet 1/2" FPT Icemaker Drain Outlet 3/4" FPT Bin Drain Outlet 3/4" FPT Icemaker Water Supply Line Shut-Off Valve Separate piping to approved Icemaker Water drain. Leave a two inch (5 cm) Supply Line vertical air gap between the Drain Valve end of each pipe and the drain.
-
Page 11: Final Checklist
G. Final Checklist 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +3°C) all year around? 3) Is there at least 6"... -
Page 12: Startup
H. Startup 1. All parts are factory-adjusted. Improper adjustments may result in failure. . If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. Do not operate the icemaker in the "WASH" position without water in the water tank. -
Page 13: Cleaning And Maintenance
Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the equipment. A. Cleaning and Sanitizing Instructions 1. Hoshizaki recommends cleaning this icemaker at least once a year. More frequent cleaning, however, may be required in some existing water conditions. -
Page 14: Cleaning Procedure
1. Cleaning Procedure 1) Dilute 16 fl. oz. (473 ml) of recommended cleaner Hoshizaki "Scale Away" or "LIME-A-WAY" (Economics Laboratory, Inc.) with 3 gal. ( 11 l) of warm water. ) Remove all ice from the evaporator and the storage bin. -
Page 15: Sanitizing Procedure - Following Cleaning Procedure
) Replace the front panel in its correct position. 3) Turn on the power supply to rinse off the cleaning solution. 4) Turn off the power supply after 5 minutes. 5) Remove the front panel. 6) Remove one end of the pump tubing. Drain the water tank. Replace the pump tubing in its correct position. -
Page 16: Maintenance
B. Maintenance This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean, soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. 2. - Page 17 6) Blow the icemaker water supply line out using the compressed air or carbon dioxide supply. 7) Close the icemaker water supply line drain valve. 3. Drain the water tank: 1) Turn off the power supply and remove the front panel. ) Move the control switch to the "OFF"...
- Page 18 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A1KQ10B...